Skip to Content

How to Adjust Genie Garage Door Opener [5-Step Solution]

Genie garage openers are a well-known brand for their reliability factor. But sometimes it may not work properly and might need a bit of adjustment. And adjusting the open, close limit, and force settings can be a hassle.

How to adjust a Genie garage door opener?

First, you need to erase the existing open and close settings that are saved. Next, you need to adjust the open and close limit one at a time. Close the garage door completely and set it as your new close limit. Do the same with the open limit. Use the force control to tweak your force settings.

Still unsure? Don’t worry! This step-by-step guide will lead you through the process.

Let’s just get into the next section!

Let’s Adjust a Genie Garage Door Opener

Genie garage door opener travel limits are programmable. This allows you to set the distance your door can travel up or down. If the limits aren’t adjusted properly then the door won’t close or open completely.

If this happens and your door opens partially then you need to adjust the up travel limit. If the opposite happens, which is the door not closing entirely then do the opposite. The down travel limit here has to be adjusted.

Genie garage door openers are also incredibly easy to transport. So don’t be concerned about the additional expense of relocating your garage.

So, how can you get your Genie garage door opener to work properly? To do so, you’ll need to follow a few basic steps.

Without further ado, let’s get started-

Step 1: Erase the Saved Settings

First, erase the previously saved settings of open and close travel limits. Find the powerhead unit memory first. On the powerhead unit control panel, hold down the “open set” and “close-set” buttons.

Push it down until the green indicator light flashes, then release it. The green light will flash once the setting is removed.

Step 2: Setting Close Limit

Genie garage door openers may be programmed to identify when the door is entirely closed. You need to activate the carriage Assembly. Press the “Close Limit” switch to drive the chain forward.

Hold the “Close Limit” button down. Keep pressing it down until the door’s bottom is solidly pushed against the floor. Hit the “close-set” limit button to establish the door’s new close position.

The green indicator light should blink once. This will mean that the new settings have been saved.

Step 3: Setting Open Limit

After your garage door is entirely open, configure the garage door opener to identify it. Keep pressing the “Open Limit” key until the door has fully opened.

Now you need to save the position of the door as the new open limit setting. Hold down the “Open Set” limit key two times. Once the green indicator light flashes twice the new position will be saved.

Step 4: Close Force Setting

Increase the quantity of force by using the “Close Force” setting. Find the buttons for “open force” and “close force.”

It’s to the right of the set and travel limit buttons. This may be found on the settings menu of the powerhead unit.

Adjust the “close force” control to the left to minimize the amount of force applied. To increase it does the opposite, turn the control to the right.

Step 5: Open Force Setting

Adjust the amount of force of the door using the “open force” option. Depending on your needs, you may turn the control to the left or right.

Reduce the force by turning it to the left. On the other hand, increasing the amount of force employed is appropriate.

Genie Garage Door Sensor Adjustment

Now, another thing to be aware of is the misalignment of Genie garage door opener sensors. If your door isn’t working properly then there might be a misalignment issue of the sensors. One side of the sensor has a green light and another has a red light.

The photo-eye with the green light should be sturdy and well connected with the wires. But, the other photo-eye is supposed to be flexible.

Check if the red light on the photo-eye flashes twice per second. If that happens it means that the sensors are misaligned.

This is very common to happen due to external hits or pressure from various things. Because the work of building a laundry room in your garage may lead to this.

So move the photo-eye and keep it at an angle where the red lights don’t flash anymore.

Once the red light stops flashing, it’ll mean that the sensors have been aligned. Now it should work without any problem.

But remember that if there is no light on then your photo-eye might be faulty or the circuitry. You may need to replace the photo-eye.

So if you are looking for some recommended replacements then here are some:

Product 1
Product 2

Hopefully, you have your photo-eye in your hands, now let’s move onto the next section.

Things to Remember

A different model of Genie garage openers might have different controls. Though the controls are different the basic process of configuring travel limits is the same.

Also, it’s better to keep the outlet of the garage GFCI protected. Since garage outlets are more prone to short circuits, it’s safer for your door opener.

You need to set a new open and close travel limit to adjust your garage door opener. Some models might have different commands or different indicators. So look for the manual and work accordingly.

Some older versions may require screwdrivers or other equipment to adjust the open and close limit.

FAQs

Question: How do I replace the carriage assembly?

Answer: First, you need to find a replacement for the carriage assembly. Then you need to remove the old one and install the new one.

Question: Is it safe to adjust the close and open limit by myself?

Answer: Yes. There is no risk factor for adjusting the close or open limit. The Genie door opener is made to be user-friendly.

Question: What if my driver’s chain breaks off?

Answer: You need to replace the chain. Any internet retailer or local hardware vendor will have a compatible chain.

Conclusion

This wraps up our article on how to adjust a Genie garage door opener. Hopefully, we were able to address all your concerns regarding this matter.

If you have any further queries do let us know. If you are still unsure do contact a professional.

Good luck!