Be Aware of Americast Princeton Tub Problems

We may get commissions for purchases made through links in this post.

You probably heard that Americast Princeton tubs are really good. But as good as it sounds, it comes with a few problems too. It’s ideal to be aware of these whether you’re purchasing one or you already have one.

What are the Americast Princeton tub problems?

Customers all over the world complained about the tub’s light layer of porcelain. It can easily be chipped off. There have been some installation problems as well. Sometimes there have been low spots in the tub, causing water to pool. 

We’ve discussed the problems and how you can deal with them. Before you buy one, you should really give this article a read. It’ll give you an idea about Americast Princeton tubs.

Problems With Americast Princeton Tub With Solutions

A lot of customers buy Americast Princeton Tub and they’re not entirely happy with it. The Americast Princeton Tubs have some common problems. We’ll discuss it now and also try to provide solutions- 

Creaking Sound

The floor helps to hold the tub in place. Thus it’s better if you install the floor underlayment. Otherwise after installing the tub, when you get into it, you might hear a creaking sound. Sometimes even acrylic tubs make a creaking noise. It’s because, without the floor underlayment, the tub will keep moving. 

Solution

Install (at least) 2″x6″ blocking perpendicular to the tub skirt. It has to be between the joists at the front, center, and back of the tub under the plywood. Your tub will be supported by this blocking.

If the floor isn’t level, shims should be used between the tub skirt and the plywood. Also, shims should be directly above the blocking. Only one shim is required at the front or rear of the tub skirt. The shim will be followed by one in the center. The skirt should come into touch with the plywood on one side.

Puddle of Water

There might be a low spot. It sometimes happens when you install the tub. Sometimes if you’re not aware, the tub may be tapped. Water is gathered in the spot and it might cause rust in the near future. 

Solution

When there’s a low spot ensure that you fix it as soon as possible. We believe that replacing the tub is the only viable solution. Inquire with the manufacturer about their suggestions. If a manufacturing defect is discovered, the tub will very certainly need to be replaced.

If the floor isn’t level, it’s conceivable that some torque is applied to the entire tub. You’ll need either a tub rigid enough to sustain itself. Or strong support beneath it for anything else. 

In addition, the tub’s top surface must be level in all directions. It’s because in order for water to drain properly and avoid pooling.

Faulty Design

The tub has a faulty design. It doesn’t have a normal overflowing drain. In future, it’ll be hard for you to replace the tub if something happens to it. 

You can also find it narrow and shallow for your bathroom if you’re not aware of the size. Sometimes the tub openings can be too big or small. The bottom may not be as smooth as you’d expect it to be. 

Solution

You should follow the instructions properly. That way, you can install the tub with ridges bottom the right way. 

Trim the support stringer to the desired length. To run the length of each of the tub alcove walls, cut a stringer out of 2-by-4 lumber.

The support stringer is horizontally connected to the alcove walls below the tub rim. Using two 16d nails, nail each stud in place.

Place the drain assembly in place. Apply putty to the provided drain assembly’s upper flange. From the inside, push the drain assembly through the opening in the tub’s bottom. Install the rubber seal, then the brass washer and nut from the outside.

The tub should be slid into the alcove and placed over the support stringers. Use 12-inch roofing nails to drive a nail into each stud slightly above the tub’s rim. The head of the nail should rest on the tub’s rim. Finally, seal the gap between the tub and the floor tile.

Chipping Off

A very thin coating of porcelain covers the tub. Sometimes the porcelain might be chipping off. Sometimes it’s not covered properly when it’s shipped. You might see some scratches on the tub. A lot of customers are not happy with the finishing.

Solution

If you’re bothered about the finishing, there’s something you can do about it. You can fix it and it’ll look as good as new! But know that, you’ll also need to maintain the tub, that’s when you need to make a temporary shower

Contact American Standard customer care and place an order for the repair kit.Ensure it matches the color and model of your tub. 

Remove any loose porcelain with a putty knife while wearing gloves. Clean the wounded area with an acetone-soaked cotton ball and let the acetone dry. 

After shaking the filler container, squeeze a little amount of filler onto a putty knife. Fill in the damaged area with the filler, slightly overhanging the undamaged region. Allow 20 minutes for it to dry.

Now the glaze in gentle layers with a paint brush. Do this until you have a nearly seamless fit. Allow each coat to dry completely before applying the next.

FAQs

Question: Is Americast better than cast iron?

Answer: When compared to cast iron and enamel steel, Americast acts as an insulator, retaining heat in water for a longer period of time.

Question: what’s the most durable tub?

Answer: Cast iron tubs are arguably the toughest tub on the market. It has a coating that resists chipping, scratching, and denting, as well as most chemicals.

Question: Which tub is the easiest to maintain? 

Answer: Fiberglass is simple to install and maintain. But it isn’t the most long-lasting of bathtub materials. 

Conclusion 

We hope now you know  Americast Princeton tub problems. We tried to explain all the problems along with the solutions to you. 

We hope you don’t face these. If you do, make sure to solve your problems accordingly.

Good luck!

Richard Allen