Water pipes leaking is a very common problem. You’re facing it too? We understand it can be quite problematic. You’ll need to block the leaking pipes in that case.
Don’t know how to do so? It’s okay, we’re here to help!
How to block a water pipe?
There are mainly 2 methods to follow for this. First of all, you can try the simple method. You can try blocking the water pipe with plastic bags and cement. You can also block the water pipe with push-to-connect fittings. This might require a little more effort than the former one.
We understand that this little idea is not enough for you to be able to fix the leak. That’s why we’ve talked about the method in detail for your ease.
Want to block your leaking pipe? Let’s dive into it right away!
- 2 Simple Methods To Block A Water Pipe
- Method 1of 2: Using Plastic Bags And Cement
- Method 2 of 2: Using Push-to-Connect Fittings
- Final Words
2 Simple Methods To Block A Water Pipe
Blocking a water pipe may sound difficult but it’s not if you pay attention to the details. You can block the water pipes in 2 different methods. We’ve provided a step-by-step process just for you.
Method 1of 2: Using Plastic Bags And Cement
This method is quite a simple one to follow. You only need to gather a few things for this method. And you can run this method following two steps only.
Step 1 of 2: Stuffing The Plastic Bags
To begin this step, you need to get some plastic bags. You can also clean and reuse your grocery bags. Because reusing grocery bags will not cost you extra money.
It doesn’t matter whether the bags are clean or not. Stuff those bags down the pipe that you want to block.
Step 2 of 2: Filling A PVC Pipe with Cement
Fill a PVC cap with a half bag of cement. Then apply concrete glue to the concrete wall. After that, cover the pipe with the cement-filled cap.
Allow the cement to cure for 2 hours. Now, restart the water pressure. And you should be done!
Method 2 of 2: Using Push-to-Connect Fittings
Before we begin, you must gather the tools that you need for this. Here’s what you’ll need-
- Tubing cutter or hacksaw
- Tape measure
Got the tools? Let’s get to work now-
Step 1 of 5: Shut off The Water
First, turn off the water supply of the house. Because you’ll need to cut each pipe’s water pipelines behind or below the shutoff valve. As a result, you’ll need to turn off the water at the main shutoff valve.
You might take longer if your shut-off valve is stuck.
With that being done, drain any remaining water or pressure from the pipes. Do it by turning on a faucet that is lower than the pipes.
As a result, the amount of water that flows out of the pipes will be reduced.
Step 2 of 5: Cut Off The Pipes
You might have enough room to revolve the tool around the pipe. In that case, you can use a tubing cutter. You can also use a hacksaw. Make sure the cut is square and neat.
Make sure the shutoff valve is turned off throughout the cutting process. Otherwise, you’ll end up with a damaged valve. The cost to replace the main water shutoff valve can put you in more trouble.
The push-to-connect caps ensure a proper seal. Also, leave as much pipe as feasible. As a result, while reconnecting the fixture, you won’t have to add an extension.
Step 3 of 5: Clean The Ends of The Pipe
Now, take a rag to clean the ends of the pipes that you just cut. ItMake sure it’s smooth and clean. You can use a hacksaw to cut the pipes. If this is the case, smooth off any rough edges before cleaning.
Now, you might be in a dilemma to choose the best rag out there! Well, no worries as we’ve got your back! Because we’ve got a couple of suggestions below-
These are the products that you can trust to use.
If necessary, use an emery cloth to smooth rough areas. But take caution not to sand the pipe down. Because it should be circular and have the same diameter as before.
Step 4 of 5: Cap The Pipes
Make a depth mark starting at the end of each pipe. Follow the manufacturer’s instructions for installing the push-to-connect fitting. The mark will indicate when the fitting is fully seated.
But if the pipe isn’t properly capped, there might be sand in the pipe eventually.
This is necessary for a good seal. Then, put it into the pipe until the pipe cap’s edge reaches the depth mark.
Step 5 of 5: Inspect The Capped Fittings
Reconnect the water supply and inspect the cap connections for leakage. Because push-to-connect fittings can be used for both temporary and permanent applications.
Most have a release function that allows the fitting to be removed with a special tool. It’s usually just a piece of plastic that you push against the fitting. To remove the fittings, make sure to use the manufacturer’s tool.
These are the two methods you can follow to block a water pipe.
Question: Can duct tape stop water leaks?
Answer: Yes, duct tape can stop water leaks. However, these are able to stop the leak if it’s of a certain size. You must use waterproof duct tape to seal water leaks. Moreover, you might also use these tapes in your kitchen and garden. These tapes can stop any small holes or leaks of water.
Question: Can I use Flex Seal to stop small leaks on copper pipes?
Answer: Yes, flex can be helpful to stop small leaks on copper pipes. Roofs, gutters, chimneys, vent pipes, campers, trailers, and other surfaces can be sealed by Flex Seal. It can also be used on wood, copper, and metals like concrete, and many more. Flex Seal can be used on painted surfaces as well.
Question: How can I temporarily stop water leaking?
Answer: Pipe repair clamps are the fastest method for this. This will prevent water from seeping into the burst pipe. And there is no need to drain the pipe before installation. Some clips are screwed in, while others are only attached to the blast area. However, the repair clip can only be considered a temporary repair.
Now, you know how to block a water pipe! We believe you found our methods simple and easy.
We hope you like our steps! Make sure to follow the instructions properly.
We wish you good luck with your home improvement!
- Plug UPS Into A Surge Protector: Things You Need To Know - December 23, 2021
- Can You Plug A Surge Protector Into An Extension Cord? [Answered] - December 23, 2021
- How to Wire a GFCI Outlet with Multiple Outlets [Step-by-Step Guidelines] - December 23, 2021