Skip to Content

Learn How to Cap Off Electrical Outlets or Get Zapped by Pikachu!

Our articles, products and services are for informational purposes. We recommend to use caution and seek the advice of qualified professionals.

Either setting up a new shelf or your kid’s curiosity to put its pinky, for many reasons you need to cap off electrical outlets. It’s a common safety concern for every house.

How to cap off an electrical outlet?

Initially, shut down the power supply to the outlet. Trim the wires. Now, cover up the wire-heads with wire caps. Finally, keep them locked in a surface mount outlet box and use a blank cover to cover it up. You must maintain the national code for wiring while working.

To properly cap off the wires, you must know about it appropriately.

Down below, all necessary information is given. So, buckle up. Here comes the party!

Time to Cap Off Electrical Outlets: Once And for All!

Well, capping off the electric wire is a common practice for any home guy. 

Whenever you remove any drywalls or you decide to put on new pairs of light, a bunch of stripped wires will always be there to greet you. 

To cap off uncovered electric wires, there are a set of steps you need to follow.

Step-01: Ready Arsenal

To start the project ‘cap of the wires’, you need some things. These things are easily available on the market. 

No need to panic about gathering them.

Here’s the list of equipment and materials that you’ll need:

  • A wire stripper
  • A box cutter or razor blade knife
  • A flat-tip screwdriver
  • Electric tester pen
  • Insulating tape
  • Marrette or wire caps
  • Surface mount outlet box
  • Blank cover

Once you collect them all, you can launch the project ‘cap of the wires’.

Step-02: Bring in The Heads

Before putting the cap on, you need to cut the wire-heads and get them ready.

For that, take the wire stripper. Remove the insulating coating around the wireheads. 

Then wires will be ready to be capped. Keep 1 or 2 inches of clean bare wires after cutting.

Step-03: Put on The Caps

Now, take the wire nuts. Wire nuts are available in different sizes. Pick the right size for your wires. 

Twist plastic caps clockwise around the bare wire. This will cover up the wires with insulated covers.

A point to remember, you don’t have to put a cap on the ground wire. 

Normally you can find three types of wires: active, idle, and the ground line. You can cap the active and idle wire, but leave the ground wire as it is. If you put a cap on the ground, then how will your panel get grounded?

Many types of wire caps are available in the market. Some of the best ones are:

Product 1
Product 2

They are the best on the market. You can give them a try!

Step-04: Add Insulating Dressing

After putting on the insulated hoods over the wire heads, give an insulating topping to your wires. 

This further ensures the protection of the electric outlet. Just take an insulating tape and put it around the caps.

Step-05: Lock It Up

Now put the cap-wire assembly in the mounted electric box. The box actually works as a frame to enclose the copper wires.

Make sure nothing is loose. Now, you won’t like a short circuit, will you?

Step-06: Cover-Up

Till now, everything’s done. 

Now, it’s time to give it a shot. Put on the blank cover over the box. Screw the bolts. You can paint the cover panels as well. 

Keep the whole assembly of wire and boxes perfectly. Any loose ends can result in short circuits. If the box is not set properly, it will be difficult to fit in the electric outlet.

The Perfect Time to Put on A Cap

Following the above steps, you can easily cap off the electric outlet. Now, the next thing that might be of your concern is, which is the perfect time for capping? 

It’s always easy to work on with copper wires when there’s no drywall around. 

These wallboards cover up a lot of space, giving you no breathing room for working. It’s better to complete the electrical work before mounting the drywall.

Caution!

Whoa, hold it right there Bob the builder! 

Just knowing the steps won’t be enough. 

You need to consider some prerequisites before working. Be very careful. These things come in handy.

Always Turn Off The Power Before Working

Shut off the electric connection before you work with the wires. 

Either you can turn off the whole power supply of your house or simply break the circuit where you’ll work. This is a very important precaution. Live lines can be deadly. 

Beware of it and avoid unnecessary risks.

As a tip, you can use the insulating tape over the switch of the circuit breaker. You can avoid any mistake by flipping the switch in this way.

Test The Wires Before Working

Test the copper wires before you wrap up the wires. 

Use a voltage tester pen. These are used in multimeters to measure voltage

This will help you to find if there’s any current in any wires. 

If the tester shows zero voltage, this means there’s no electricity flow and it’s safe to work. Otherwise, you have to do the rewiring.

Remove Electrical Outlet

There can be devices connected to the electric outlet. Remove those devices before working.

Wear Basic Safety Kits

Wear the necessary gear to protect yourself from any injuries. 

Accidents can happen even after taking precautions. 

Wear insulated boots, gloves, while working. Also, check if your tools are properly insulated as well.

FAQs

Question: Does capping off electrical outlets require an electric permit?

Answer: Electrical permits are required in any electrical installments. Apparently, it is not mandatory to have an electric permit for the usual electric wiring. If you are doing this for any bigger institutions or buildings, then you will need a building permit.

Question: Does the color of the electric caps matter?

Answer: Yes it matters. Wires can be of different sizes and shapes. So do the wire caps. The color specifies the size of the caps. Wrong caps can be too small or too large for the wire. Watch out for the color.

Question: Can I set furniture in front of an electric outlet?

Answer: If the outlet is covered and it is approved by the code, then you can place the furniture. Be careful if there’s any loose wire out. 

Epilog

That is all I have for you builder. Now you know how to cap off an electric outlet

Hope you have covered up the wires nicely and safely.

I’ll take leave now. Stay safe.

Happy home fixing!