With winter arriving, most of us with fireplaces are getting it ready for the cozy nights ahead. If you especially own a brick fireplace, you may like to clean it properly before using it. One way to do that is using scrubbing bubbles.
How to clean a brick fireplace with scrubbing bubbles?
First, you can try cleaning it without any other cleaning agents. If not, then you may use soap and table salt to clean it properly. Finally, you can use vinegar to create scrubbing bubbles to clean your brick fireplace!
You’re at the perfect momentum to get to the main part. Manage a bit of time to keep on reading to know more!
Don’t waste a second! Get started now!
Make Your Brick Fireplace Dust Free With Scrubbing Bubbles
Scrubbing bubbles are good enough as a cleaning agent for multiple substances. But most people don’t know about its use in a brick fireplace.
Today, we’ve covered 2 simple methods to use scrubbing bubbles to clean a brick fireplace. If you can’t clean it properly, the wall might get hot with the fireplace turned on. Take a look at the methods given below-
Method 1: Cleaning Without Any Other Agents
This method is the basic and simplest method used quite often. It is really simple without any necessity for any other supplies. We have got a step by step guide so read through it-
Step 1: Put A Towel On The Floor
First, put a piece of a towel over your floor or near the fireplace’s base. It should be under the area you’ll be cleaning. This will safeguard the fireplace’s floors and other areas. As a result, it won’t absorb any soot or cleaning solution.
If you don’t put on a towel, you might be going through hazardous consequences. Any soot particles can light fire gradually leading to a fatal accident.
Step 2: Scrub The Brickwork With A Damp Towel
Scrub the brickwork of the fireplace with a towel dampened with warm water. The loose soot will be removed, making the cleaning process easier.
If you’re having a dry cloth, it would make it harder for the cleaning process. It could take away more than the actual time to clean it.
Step 3: Spray Scrubbing Bubbles
Now you need to spray scrubbing bubbles on the fireplace bricks. Spray directly onto the fireplace’s bricks. Then you must apply a thick layer of bubbles on the bricks. Allow three minutes for the cleaning solution to sit.
Step 4: Scrub Off The Cleanser
Using an old toothbrush, scrub off the cleanser into the bricks. This will make getting inside brick crevices much easier. This would also clean the spaces between the blocks. Repeat the process until the entire surface is clean.
Using a warm towel, saturate the brick fireplace and wipe it down. This will collect any residue that has become dislodged. This would also gather any leftover cleaning solution from the scrubbing bubbles.
If necessary, repeat until the fireplace is clean to your satisfaction.
Finally, you’re done cleaning your brick fireplace using scrubbing bubbles!
Method 2: Scrubbing Bubbles With Soap And Table Salt
This method can be a bit lengthy but surely a good one. You may need a few more additional supplies for this. But this can clean your fireplace quite neatly. And this is a great cleaning method when you’re removing the fireplace.
Without any further due, let’s get started with the steps given below-
Step 1: Remove The Soot Particles
First, you must remove the loose soot and ash. Or else, when you start adding water, you’ll have a dust mess on your hands.
A broom is required to clean loose ash and soot. You also need a vacuum cleaner. Because this is going to be dirty, it’s also a good idea to lay down an old sheet.
Now, brush the bricks properly using the broom. Then connect the broom with the vacuum cleaner to take out all the soot particles.
Step 2: Combine Soap And Table Salt
Cleaning fireplace bricks using soap, or salt and a bristle brush are safe and inexpensive. To begin, combine one ounce each of dawn dish soap and table salt in a mixing bowl.
Then add an adequate amount of water so that the mixture forms a cream. Wrap the bricks with the aforementioned mixture using a dishtowel. Allow 10 minutes for it to soak.
Step 3: Scrub With A Brush
Now scrub with a bristle brush. Do it in a circular motion. You’d notice the scrubbing bubbles which is a good sign. To get a bit more scrubbing action, spray water on the solution. Rinse and clean the surface.
If necessary, repeat the process.
Are you confused about the type of brush you can use for this? Well, no worries! Because we’ve got you a couple of suggestions below:
These are the bristle brushes that you can use for multi-purpose stuff!
This is how you can be done cleaning your brick fireplace.
Method 3: Scrubbing Bubbles With Vinegar
Vinegar is probably not the first thing that comes to mind when thinking about cleaning solutions for fireplace brick. The acidity of the vinegar, on the other hand, is excellent for breaking down the build-up on bricks.
But keep in mind the age of your bricks. You could have bricks that are 20 years old or older. In that scenario, vinegar may not be the best option. You’ll need to take a few steps to get started with vinegar’s cleaning capabilities.
Step 1: Combine Vinegar With Water
Combine equal parts vinegar and water in a spray bottle. Give the inside of the fireplace’s brickwork a good soak. Then spray the outside of the brickwork. Now, allow 2 to 5 minutes for the process to complete. Then spray once more.
Step 2: Add Some Dawn Drops
You may need to add more scrubbing powder now. In that instance, add a few drops of dawn to the mix. Then thoroughly rinse and wipe down the brickwork. As needed, repeat the procedure.
Fill the spray bottle with a few tablespoons of baking soda and water. You may also use an abrasive cleaner for this. This would balance out the vinegar’s acidity.
Then spray the bricks with water and let them dry. And you’re done cleaning the fireplace!
These are the methods you can follow to clean your brick fireplace with scrubbing bubbles. Go through the instructions thoroughly. Make sure you don’t skip any of the given instructions or steps!
Question: How can I clean a burnt brick?
Answer: To begin, fill a bucket with 1 gallon of water. Then add 1 liter of cola and 1/2 cup all-purpose detergent. Soak a sponge in the cleaning solution. Place the sponge on the brick that has been saturated. Then push the sponge against the block to distribute the cleaner. Keep doing this until the cleaning solution has completely covered all of the burnt brick.
Question: How do I restore the brick fireplace instantly after cleaning?
Answer: Vinegar is a mildly acidic liquid that is frequently used to clean bricks, stones, and grout. To begin, spray the fireplace with a 50/50 mixture of vinegar and water. After a few minutes, it sits for a few minutes to allow the acid to do its job. The fireplace should next be scrubbed and sponged clean.
Question: Can I make the bricks look new?
Answer: Yes, you can make bricks look new. First of all, scrub the brick with a bar of dish soap and table salt mixture. Then mix 1 cup (0.24 L) of dish soap and 1 cup (0.24 L) of table salt together. This would form a paste that could be dispersed. Now, apply a thin coating of paste to the entire area.
The Final Words
Now you know how to clean a brick fireplace with scrubbing bubbles! We believe our instructions are helpful to you to carry out the processes.
We hope you find our article helpful enough!