How To Remove Floor Tiles Without Breaking Them [Explained]

We may get commissions for purchases made through links in this post.

You may have put those wonderful floor tiles in with all your heart. But you might need to remove them at a point for numerous reasons. The tiles may need to be completely replaced if they are broken. But how to do it properly!

How to remove floor tiles without breaking them?

First, you can try out the traditional method to remove the tiles. If that doesn’t work out for you, consider using a hammer drill for this. Finally, you can take help from the experts to take off the tiles without breaking them.

You just got a peek through to the main part. Manage some time to read along to get to the main part.

Keep reading below and you will find the full answer!

3 Methods To Remove Floor Tiles Without Breaking Them

As this process is quite sophisticated, we’ve got a few simple ways to do it. You can simply follow the steps to carry out this complex operation easily. Take a look at the methods given below-

Method 1: The Traditional Method

This method can be a bit longer compared to the rest. But this is surely one of the best and easiest methods to consider. It is simplified in 3 main steps below-

Step 1: Take Out The Grout

The very first thing to deal with while removing tile is the grout. It might also be silicone instead of grout as it’s the alternative at times. You may think it is impossible to remove this rigid substance. But you can actually remove it easily with the ideal tools. 

Ascertain that the grout is properly dealt with. In that situation, you’ll need the assistance of a grout saw. This is a gadget that makes it simple to cut cement grout.

To begin, hit on all over the grout surface with a decent force. Then take out the grout gradually. It might take a while, but don’t give up! Keep on taking out the grout from the tile gap.

Step 2: Keep Out Any Cracks

You’ve now cut the grout from between the tiles and removed it. This step would be much simpler if grout goes bad. The next step is to keep any cracks to a minimum by masking tape. 

To begin, rip two pieces from each tile and cross them in the center. Do it in a way that makes it appear as if you’re trying to pry them off the floor. The vibrations will be absorbed by the masking tape, reducing the chance of cracking.

Step 3: Remove The Tiles 

It is a truism that removing the first tile is always tough. The rest, on the other hand, are relatively simple. The goal is to go slowly and methodically, as well as to work in a well-planned manner. 

Place a putty knife along the grout line that has been cut. It should be cut at an angle so that it gets close to the surface. Tap the end of a rubber mallet slowly. Work it under the tile until it’s completely covered. 

Remove the putty knife from the previous edge and replace it at the next edge. Rep the process until all of the sides have been completed. In the center of the tile, place a suction cup. Then, through the hole, thread twice.

Not sure what putty knife to use? Look at the suggestions below-

Product 1
Product 2

You can count on these products without any hesitation!

When you pry the tile apart, don’t pull off the rope too hard. Then remove the remaining tiles. You must also be cautious when storing the removed floor tiles. Try not to stack them, and if you do, do it cautiously. 

Finally, you’re done removing the tiles.

Method 2: The Hammer Drill Method

This method is also simple to operate. But you need to have a hammer drill to follow this method. Once you’re ready, get to the steps given below-

Step 1: Remove The Baseboards

To gain access to the full tiled surface, remove the surroundings of the baseboards. A drop cloth should be used to cover any surfaces in the room. This would keep shards of tile and dust out. 

Use a plastic sheet to cover the room’s entrances and vents. As a result, dust will not be able to escape the region. 

Make sure to wear work gloves and safety goggles. This will prevent any injuries from occurring when removing the tiles.

Step 2: Remove The Tiles

To the hammer drill, add a chisel tip. Hold the drill at a 45-degree angle with the tip on a grout line between tiles. Toggle the drill’s hammer mode switch and start the drill. 

When it starts to chip into the grout, keep it steady and gradually advance the drill. 

Continue working your way along the floor, from the center to the edges. Chip away at all of the tile using the hammer drill. Sweep the tile debris with a broom to remove it. And you’re done with removing the tiles!

Remember that this can be a good method to take off tiles from plasterboards!

Method 3: Calling Out An Expert

It is not that easy to remove the tiles without breaking them. And we know how subtle it is by reading the first method. Now, you might think of making it risk-free. If that’s the case, reach out to an expert. 

What you have to do is reach out to  a professional in this field. They can remove the tiles without breaking them quite easily. Although, it might be a bit costly to operate the process.

FAQs

Question: How difficult is it to remove the floor tiles?

Answer: Removing floor tiles is a time-consuming and tough task. And the difficulties are frequently disguised until the project is well underway. The tile might be attached on bare cement, depending on the construction. It can also be nailed to a piece of plywood or a piece of mason board. The floor tiles might be glued down to an existing floor which makes it quite tough to remove.

Question: Can I reuse the floor tiles after removing them?

Answer: No, you can not reuse the floor tiles once you remove them. The reason for this is that tile is frequently attached with thin-set mortar or epoxy. The mortar blends in so well with the tile that it almost becomes a part of it. Even if the tile can be removed, the bottom is uneven and unfit for reuse.

Question: Is it okay to put laminate over the tiles?

Answer: Yes, engineered wood or laminate flooring can be installed over tile. You must ensure that the condition of the tile is good. Your installation would not work if there are loose tiles. The tiles can not be damaged anyway. If you’re going over tile, you’d require engineered hardwood flooring that has been prefinished. Depending on the manufacturer, the floor will be bonded or floated.

The Final Words

Now you know how to remove floor tiles without breaking them! Make sure you follow the instructions properly.

We hope you find our instructions really helpful! 

Best wishes!

Melissa Hawkins