We know it can be difficult to decorate a concrete wall. Especially hanging something becomes a nightmare. Don’t worry, we have just the guide to save you from this dilemma.
How to hang a picture on a concrete wall?
There are 3 different methods you get to decide between. The first one is the adhesive hooks. The next one is to use hard wall hangers. Finally, we have the masonry anchor one! Choosing one will depend on a few important factors.
We know how curious you might be to know the full details.
Let’s jump into our segment!
- 3 Different Methods To Hang A Picture On A Concrete Wall
- How to Hang A Picture into Concrete Wall Without Drilling
- How to Hang A Picture into Concrete Wall With Drilling
- Bottom Line
3 Different Methods To Hang A Picture On A Concrete Wall
You can choose from three options to hang your picture. You can decide between them using their features!
Let’s start off with a brief summary on these:
|Adhesive Hooks||Hardwell Hangers||Masonry Anchors|
|How To Use||Stick onto Wall||Hammer into Wall||Drill it into Wall|
|Weight Capacity (pounds )||0-8||0-25||25 and above|
|Time Required||2-3 minutes||5-8 minutes||5-10 minutes|
|Tools Required||None||Hammer||Electrical drill or hammer drill|
Now we have an idea about what we’re getting into! Let’s check out their Infos.
How to Hang A Picture into Concrete Wall Without Drilling
There are two ways to hang a picture without actually drilling on your wall. There’s one using an adhesive hook and another one using a Hardwell hanger.
Method 1 of 2: Using Adhesive Hooks
These hooks have adhesive on their back. Thus they can stick firmly on the wall. You can opt for two hooks. This will better support your picture!
Let’s check the steps to install it.
Step 1 of 3: Prep Your Wall
Start by cleaning the wall portion where the hook will be placed. You can use a paper towel dipped in rubbing alcohol for this. Cleaning the surface will also help the adhesive stick better.
You can also use soapy water as an alternative. But dry it before you move any further. You can also use any type of abrasive to clean your surface.
Step 2 of 3: Mark The Spot & Stick The Hook
For this use a pencil to mark the spot. Find the exact place you want the hook to be installed. Then mark it precisely.
Remove the plastic cover from the adhesive. Line up the hook straight against the wall. Press it to the wall with a decent amount of strength. Press it on for 30 to 45 seconds before releasing it.
Step 3 of 3: Allow The Adhesive To Dry
Now, you’ll have to wait for the adhesive to dry. It’ll take about 30 to 60 minutes. After that, hang a bag or something on the hook to test it.
Once you’re certain the hook won’t fall, you can hang your picture.
Method 2 of 3: Using Hardwall Hangers
These hangers will be perfect for the massive portraits. Again, you can use two for more support. Now, onto the steps.
Step 1 of 2: Mark The Spot
Mark a dot where you want your picture. Follow the steps we did for adhesive hooks.
In the case of two hangers, measure the distance between them. Then mark the spot according to that measurement.
Step 2 of 2: Install The Hanger
For this, place your hanger on the marked spot. Hold the hanger on the wall. With your other hand, gently nail the 4 pins with a hammer onto the wall. But only do it halfway.
Release the hangers and check whether they’re in the same position. Because if you position one off-center, the other might also be crooked.
After checking it, if you think the position is right, you can nail it all the way. If not, take it off, mark your spot again, and then nail it.
What if you want to hang some bigger frames? Then look no further.
How to Hang A Picture into Concrete Wall With Drilling
For this, you can buy a masonry kit. It includes everything you need for the process. Similarly, for better support, use two anchors.
Wondering where to find the masonry kits? Well, we have some amazing recommendations:
Check these out! These are the best of the best you can choose from.
Step 1 of 2: Drill A Hole Into The Wall
Mark the spot just like you did in the adhesive hook installation. Then you can use a hammer drill or a regular electric drill. But a hammer drill is preferred over an electric drill.
Use it at a slower speed for better results. But maintain a firm grip.
Step 2 of 2: Place The Anchor In The Hole & Add The Screws
Tap the anchor until it’s completely flushed into the wall hole. If you see that the hole is a little too snug, try expanding the hole a bit. Redrill using a slightly larger bit. It’ll fit easily then.
Put your screw in the anchor using a screwdriver. But don’t screw all the way. Leave off about ½ or ¾ of a centimeter. This is where you’ll place the wire at the back of your picture frame.
You can also install your wall cabinets with this method! Instead of the screws, you’ll use studs.
You can finally hang your pictures now!
Question: Do Command Strips work on concrete?
Answer: Sadly, it’s a no. You can use this on smooth surfaces only. That too after these are cleaned with isopropyl rubbing alcohol. Thus we have to avoid using this on concrete walls.
Question: What is the best adhesive for concrete?
Answer: Adiseal is simply the best one to use on concrete. By an independent test, they are proven to be the strongest adhesive. They are known to stick to any type of surface.
Question: Can Gorilla Glue be used on concrete?
Answer: Yes, gorilla glue can be used on concrete. These are water-resistant, versatile, and tough. Moreover, they have a strong grip on the surface compared to other glues.
This brings us to the very end of our segment. Hope this guided you on how to hang a picture on a concrete wall.
Make sure you safely hang your picture. We wouldn’t want it to fall off.
Until next time, adios!
- Wire Gauge & Ampacity Basics: Guide to Select The Right Wire Size - September 24, 2021
- Water Softener Black Sediment: What ToDo About It? - September 23, 2021
- Drop Ear Elbow Install [4 Easy Steps] - September 23, 2021