Skip to Content

How To Install A Bathroom Faucet With Pop Up Drain In 6 Easy Steps

Installing a pop-up drain is not easy. But it’s not impossible either. There are a lot of preparations and calculations that must be done first. That’s why you’ll have to follow certain steps strictly. 

How to install a bathroom faucet with pop up drain?

You’ll have to disconnect and remove the old drain first. When done, disassemble the faucet to take it out. You’ll then have to install some washers on the threaded tubes. Place the faucet properly after connecting the tubes. Install the drain collar and connect the pop-up drain. You now have to adjust the clevis strap and check for leakage. 

Anyhow, that was a short summary of the entire process. It’s very complex and requires further elaboration. That’s why we’ve explained each of these steps in detail. 

Read along if you wish to know more about the installation of pop-up drains.

Why Should You Have a Pop-Up Drain? 

A pop-up drain is a push-button system that seals the sink instantly. It has many benefits.

Prevents the Hair Clogging the Drain

Hair is one of the most common reasons behind a clogged drain. Some people also assume they can flush hair down their toilet. But it’s actually detrimental. 

With a pop-up drain installed, your hair won’t go down the sink. It catches almost all the hair which you can grab later and throw away. 

Debris Can’t Get Inside

Whenever we wash dirty objects, debris can enter the sinkhole at any time. But a pop-up drain prevents that. 

Any sort of debris or very small hard objects won’t be able to pass through. This keeps your sink and drains safe.

Makes Your Life Easier

Using a pop-up drain can enrich the quality of your life. You now don’t have to worry about hard objects entering the sinkhole.

You also don’t have to deal with any sort of mineral deposits. Pop-up drains reduce the waste of water and keep the supply lines functional. 

Installing a Faucet With Pop-Up Drain: 6 Simple Steps

There are a variety of problems regarding bathroom faucets. For example, bathroom faucets can become noisy or the handle might become loose. 

But luckily, fixing most of these problems is very easy. Plus it takes only 5-10 minutes. This problem isn’t an exception either. 

These tools are required to begin the installation-

  • Mechanical Pop-up drain 
  • Plumber’s Putty
  • Channel-lock Pliers
  • Crescent Wrench
  • Container
  • Clothes

Manage these components as soon as you can and we can get started! 

Step-1: Turn Off the Water Supply & Detach the Drain

Before everything else, we have to meet certain prerequisites. Start by turning off the water supply. 

Turn on the faucet then drain it entirely. Look for the P-trap installed below afterward. Place a bucket beneath it and open the cap to drain it. 

Get the channel-lock plier to unscrew the drain nuts. Unscrew the top nut above the P-trap and repeat the same for another nut. Do the same to the back nut. 

If the P-trap has no drainers, simply pivot the P-trap away from the pipe. 

Step-2: Remove the Old Drain 

You can now safely remove the old drain. Get the channel-lock plier or crescent wrench. 

Use the pliers or wrench to loosen the nut that is beneath the sink. When the nut comes off, it will expose the rubber gasket. Grab the gasket and take it out. 

Hold the drain and push it upwards after that. It will detach itself from the putty and you can then take it out. 

Step-3: Replace the Faucets

If you’re replacing the faucets, there is some extra work to do. You have to remove the old sink faucet completely. 

Place both nylon and rubber washer on the threaded tube of the single faucet. If there are no washers, insert a nylon plate and a rubber gasket instead. 

Position the new faucet by inserting its lower end into the faucet slots. Insert the provided washer or gasket from down below afterward. Tighten the nuts with a crescent wrench. 

Grab the fitting and screw it to the threaded tube. Likewise, screw it to the main pipe afterward. Use the channel-lock plier to tighten the fittings. 

Step-4: Replace the Plumber’s Putty

Detaching the drain will leave the sinkhole with dirty putty. Since they are quite old, it’s best to remove them entirely. 

Grab some clothes and water. Pour some water around the sinkhole. Use the cloth then to take off the old putty. If the putty is too sticky, pour some more water and let it soak. 

After the putty removal, apply a new putty. Grab some putty and roll it with your hand. Once it becomes shaped like a snake, put them around the sinkhole. 

To save some time, we’ve listed some of our favorites- 

Putty 1
Putty 2 

This will let you pick whichever you prefer and get started! 

Step-5: Place the New Drain Collar

All the removals are done. You can now begin the installation of the new drain. Get the new drain pipe and the channel-lock plier. 

Carefully insert the drain pipe through the sinkhole. It mustn’t touch the putty.

Place the collar on the putty and apply moderate pressure on it. This will let out the excess putty around the collar. Let it stay there for now. 

Get the rubber gasket and insert it onto the shaft. When done, insert the washer and tighten the nut with bare hands. 

Sometimes, the drain pipe can be too high for the sink. In that case, you’ll have to improvise a little bit. 

Get the mechanical pop-up drain and screw it at the end of the drain. The pop-up drain must face the back of the sink. 

When you find the position, tighten the washer nut. Use a plier or a crescent wrench for that. Take out the excess putty from the sinkhole after that. 

Step-6: Install & Adjust the Clevis Strap 

This is the final part of the installation. The clevis strap is the mechanism that allows you to adjust the pop-up space. If you can do all these steps, you can surely fix your loose Moen bathroom faucet when needed.

Going back to the step, Insert the pop-up stopper through the drain collar. Get the pivot rod. Screw it at the back of the pop-up drain. Grab the extension rod and insert it using the hole behind the faucet. 

Insert the pivot rod into any extension rod holes. Use the provided clip to attach it firmly. 

You can now test the pop-up by lifting the rod. Keep adjusting until you find the right height. When done, run the water and check for any leakages. 

Anyhow, this installation can seem tough to you. In that case, don’t hesitate to call the nearest plumbing service! 

If you are still wondering which faucet to get. You can look into Pfister and Delta faucets as they are popular in the market.


Question: Do faucets come with a pop-up drain?

Answer: Faucets do not come with a pop-up drain. But they do provide a drain stop. Some of the models also provide a lift rod and related attachments. 

Question: Why does my bathroom sink stink?

Answer: It’s most likely to be a bacteria outbreak issue. It can be caused if the sink isn’t washed frequently. Food or grease build-up can easily make your sink stinky. 

Question: How do I fix a smelly bathroom sink?

Answer: Take one cup of baking soda and two cups of white vinegar. Run hot water for 2-3 minutes. Pour them down the sink and wait for an hour. Clean the sink afterward with cold water. 

Final Words

That was everything on how to install a bathroom faucet with a pop up drain. Hopefully, we were able to clear your confusion regarding this topic. 

Finally, best of luck!