Skip to Content

How to Install Carpet on Concrete Floor With Glue [8 Easy Steps]

You want to put carpet down on your concrete slab. If you use glue, installing carpet immediately over concrete might be a do-it-yourself project. But you’re not sure what to do.

Ok, I might have had the perfect snippet to clear things up for you!

How to install carpet on a concrete floor with glue

You could either glue the carpet directly to the floor or glue the flooring to the carpet pad you previously installed on the concrete floor. Prepare the floor by measuring, and cutting the carpet. To solve lifting-up issues, drizzle the adhesive and wrap over the cut piece on the concrete.

If you have a little time, we’ve produced a comprehensive essay that details each of these stages.

Let’s get started!

Ways of Install Carpet on Concrete Floor With Glue

Carpet flooring is still one of the more popular choices for homes and businesses. The ease with which a carpet may be cleaned is one of its key advantages. You should be aware of the cleaning process. You can use a wet vacuum cleaner to clean your carpet.

In commercial settings, glue-down placement is the most common carpet installation type. The carpet is attached directly to the floor with this type of installation. 

The floor must be quite smooth. Any faults in the flooring will be seen through the carpet.When you glue the carpet to the concrete floor, these are the steps you need to follow.

Step 1: Concrete Preparation

The success of caulk carpet installations is determined by the status of the ground. The moisture content that your carpet may be exposed to is one of the most difficult aspects of putting carpet on concrete floors. 

So, before you put in your flooring, ensure the floor is spotless and fully cured. In addition, you must repair fractures, low and high spaces, remove old adhesive off the floor, and other flaws. If these flaws are not addressed, the carpet will likely wear and tear fast.

Step 2: Carpet Preparation

Make sure the carpet is clean and ready to be put down. Roll down the carpet fully and let it rest and breathe for a few hours before moving on to the next thing. 

Make sure the carpet is facing down when you start your day. Turn the plush side down and spread it out flat on a flat surface.

Step 3: The Carpet Should Be Measured And Marked.

The next step is to measure the flooring, trying to add 0.5 feet to a length. Label the measured data on the bottom of the carpet with caulk. To ensure that now the carpet sides are straight, use a straight edge.

To complete this step, you must understand how to measure carpet.

Step 4: The Carpet Should Be Cut to Size

Using a carpet knife and cutting the carpet to fit the dimensions of the room while it is face-down. Also, make sure that all of the sections that go around the cabinets are appropriately cut. Re-roll the carpet out to one end of the room after it’s finished.

Step 5: Putting Glue on the Carpet

Place the carpet edge that has been cut and rolled against the wall. Place the end of the carpet roll against the wall with caution. In a nutshell, make sure the carpet is ready to go.

Directly adjacent to the carpet roll, apply a thin layer of carpet glue (approximately 36 inches thick) to seal the carpet in place. When it comes to setting the glue, follow the manufacturer’s directions.

You can purchase your carpet glue from these recommended products below:

product 1
product 2

These will be the greatest alternatives available. So, you can use it without reservation!

Step 6: Roll the Carpet on Top of the Glue

Roll the carpet gently into the adhesive surface. Use a flat board to press and flatten it. Reapply glue to the ground and roll the carpet throughout the room.

Step 7: Glue the First Edge Down

The carpet’s initial margins, in which the roll was first laid, were not glued. Finally, we’ll use some glue to secure the raw edges.

Apply the glue by pulling the carpet away from the wall. Using a flat board, flatten the edges of the carpet by pushing it against the wall until the thin layer of glue has cured.

People frequently become puzzled as to how to properly seal their carpet edges. They frequently contact a professional. However, this is not necessary because the procedure is quite easy.

Step 8: Finishing

After you’ve covered the entire room with glued-down carpet, you’ll need to trim the extra flooring from the borders where the walls meet the floor. To ensure that the edges are cut into shape:

  1. Use a carpet knife.
  2. Lay down heavy objects on all four corners to keep them firmly in place and to help keep your carpet flat as the glue dries and hardens.
  3. Let the pieces sit for at least one night to dry the adhesive completely.

That’ll be sufficient to vanish any soap there is from your carpet.

FAQs

Questions: What type of carpet glue do you use?

Answer: Anything with glue will work as a general rule. Acrylic, smooth material, Elmer’s adhesive, PVA glue, floor glue, or mask latex are all examples of this.

Question: How much time does carpet glue take to dry?

Answer: Carpet glue normally dries in 48 hours. After gluing your new carpet, you can walk on it, but don’t move any furniture for at least 1 day. Excessive force or weight on the newly bonded carpet will permanently destroy it.

Question: Is carpet glue water resistant?

Answer: It’s solvent-free and waterproof! This high-quality marine glue works on all of our outdoor carpets, regardless of backing design. Over marine chipboard, coated plywood, fiberglass, metal, and even concrete or asphalt.

Final Words

That’s all I have to say about how to install carpet on concrete floors with glue. Hopefully, you will find the information provided useful.

Additionally, don’t forget to maintain your carpet. Maintaining your carpets is really important.

Have a fantastic day!