Skip to Content

How to Install a Clothesline Tightener [5 Simple Methods]

Drying your clothes on a sunny day in the backyard feels good. But not if the clothesline is sagging and getting caught up in the mud. Don’t worry, we’re here to help you save time.

A clothesline tightener is simple to set up.

How to install a clothesline tightener?

Start by holding one side of your clothesline using a clothesline tightener. Next, wrap one end of the rope around your pulleys. Then return the other end to the tightener. Enter the rope into the knob. Finally, pull it out from the other side and cut the extra rope.

So, if you have a few minutes, let’s get started right away!

5 Steps to Install a Clothesline Tightener 

In this segment, I’ll be talking about the installation process. The process isn’t too tough like unscrewing hex screws without using hex drivers.

But first, you’ll need to collect a few items.

What You Will Need 

  • A clothesline tightener
  • Pair of clothesline pulleys installed
  • Scissors
  • Clothesline rope
  • A piece of wire

So no need for a carpenter if you have all of your tools. So, let’s dive into the installing methods-

Step 1: Binding the Clothesline with the Tightener

Firstly, hold one end of your clothesline and bind it with the hooked end of the tightener. 

Make certain the knot is secure.

Step 2: Wrapping the Clothesline to the Pulleys

Wrap the other side of the clothesline all-around around pulleys after that. Then bring the clothesline back to the tightener. 

Step 3: Putting the Clothesline into the Tightener

Thirdly, twist around a piece of thin wire to the loose end of the clothesline. Then pull the knob of the tightener and insert the wire through it.

Step 4: Getting the Clothesline Out of the Tightener

Then, once it’s tight enough, pull it all through the other end. Be careful while pulling. Don’t overdo it.

Step 5: Cutting Excess Rope

Finally, cut the extra rope off, but leave at least 12 inches for tightening later.

So, these are the necessary steps. Here, we have provided you with directions from the start to the very end.

How to Wire a Clothesline?

Now, you will learn the wiring process. For that, you also need some equipment. 

But before that crosscheck some things again. Check if anything is unnecessarily attached to the clothesline. For example, old masking tape then just remove the tape

After that proceed to gather the necessary equipment for installing your clothesline.

Equipment You’ll Need

  • Wire clotheslines
  • Pulleys/tee-shaped poles
  • Measuring tapes

Now let’s move to the main part.

For Pulleys

Measure the distance between pulleys. Calculate the length of wire that you will need. It should be double the calculated distance plus the length needed to loop around.

Using a long wire, loop it around both pulleys and tie it in a tight knot.

For Tee-Shaped Poles

Measure the distance between both poles. The proper height of the horizontal bars on top of the poles must be measured.

Decide how many lines you’d want to run over them. At least one foot should separate each pair of lines in each bar. And no more than two lines flowing through it.

The distance between poles should be equal to the number of lines you intend to run. 

Tie the wire to the poles with plenty of excess lengths.

Wrap the wire over to the other horizontal bar and tie one end to one pole. Run the wire all-around bar again after scooting the rope one foot to the side.

Tie the wire around the other horizontal bar and tie one end to one pole. Tie the wire around the pole again after sliding it one foot to the side.

Why Do You Need a Tightener?

Clothesline might get loose frequently, which causes clothes to reach the ground. And then the clothes become dirtier than ever. If the clothes are wet then it adds more to your chores.

In this scenario, a clothesline tightener is your lifesaver. It keeps away the rope from sagging. It also combats the unavoidable effects of gravity on the clothesline. 

Few Tips and Warning for You

Now, I will describe a few tips and warnings about installing a clothesline tightener:

  • After putting the clothesline through the knob, tie a knot at the end. So that if you are going to loosen it, it doesn’t shoot right out. 
  • Use line spacers to keep the lines closer while drying heavier items.
  • To prevent the clothesline from sagging, tighten it at least once a month. 
  • Do not tie the clothesline too tight that they cannot move easily around the pulleys.

These are some tips and warnings which may be handy for you. 

Another thing, while doing the process stay concerned about not getting a stain in the cloth. Even if you mix up with stains like grease, clean the stain as soon as possible.

If you are looking for clothesline tighteners for yourself, you can give the given below, clothesline tighteners a shot. They are pretty good at their job.

Product- 1
Product- 2

These are some of the really good clothesline tighteners around. They are also quite durable. Hence, they should last a long time.


Question: What is the work of a clothesline spacer? 

Answer: Clothesline spacers keep both lines of the pulley system consistently separated. That prevents a variety of issues that can arise in rainy or windy conditions.

Question: What type of rope is good for a clothesline

Answer: Nylon can be a good choice as a clothesline rope.Because they are very durable and also water-resistant. So, it won’t get super slippery.

Question: Why do clotheslines sag?

Answer: Even if nothing is hung from it, a clothesline sags slightly. Because the clothesline has a limited mass. To counterbalance gravity’s downward effect, the strain in the line must have an upward component.


We hope that how to install a clothesline tightener is understandable. It’s a quick task that takes 2 minutes to accomplish. You can also install it by yourself, saving you time and money. 

Now you can dry your clothes without worrying about them becoming dirty.

Good luck with your clothesline tightener!