Skip to Content

Kitchenaid Dishwasher Reset [2 Simple Solutions]

When your Kitchenaid dishwasher fails to operate correctly, it can be pretty problematic. But there’s nothing to worry about. It can be fixed very easily. Don’t call an expert right away if you observe any glitch in your dishwasher. You can solve this complication yourself by simply resetting it.

How to reset Kitchenaid dishwasher?

There are 2 ways the Kitchenaid dishwasher is reset. The first one is ‘Manual Reset’ and the second one is ‘Control Panel Reset.’ Manual reset is the simplest one. You just have to unplug and plug your dishwasher after a while. If the manual reset doesn’t fix the dishwasher, you’ve to proceed with the control panel reset.

This was just the teaser of what we have here. Read our article to know the details and reset your kitchenaid dishwasher. 

Let’s jump into the details!

Why You Need to Reset A Kitchenaid Dishwasher

Kitchenaid dishwashers are one of the most reliable home appliances out there. It rarely malfunctions and gives any trouble. Still, there are times once in a while when it might not work correctly. 

But how to understand when you need to reset your KitchenAid dishwasher? Don’t worry, we’ve got the signs by which you’ll know it’s time for a reset:

  • There is a ‘Clean-Complete’ light on your Kitchenaid dishwasher. The light keeps blinking.
  • If your dishwasher fails to advance a cycle.
  • There would be times when your dishwasher would fail to run altogether.
  • Due to power interruptions.

Now, let’s look at how you can reset your dishwasher!

How To Reset A Kitchenaid Dishwasher? 2 Different Ways

Your Kitchenaid dishwasher suddenly stops working doesn’t mean it’s broken and needs to be replaced. You can fix your dishwasher yourself within a few minutes by resetting it. 

We provided  2 different methods you can follow to reset it. Usually, a manual reset fixes the problem. But if it doesn’t, you have to perform the control panel reset. To avoid any confusion, check if the clean light of the dishwasher is in perfect condition or not.

Let’s see how these reset procedures are done!

Method 1: Manual Reset

The manual reset is somewhat similar to when we reboot our computer to deal with some bugs. You need to perform the same steps in the case of a Kitchenaid dishwasher as well. You can do this method in two ways.

To perform this reset method, first, turn the circuit breaker off that powers your dishwasher. Then wait for at least five minutes. During this time, your dishwasher unit may be recalibrating or diagnosing the bugs. 

After the five minutes is over, turn the circuit breaker back on.

You can perform this reset method in a different way, almost similar to the previous one. First, you need to unplug the dishwasher from the power socket. Then wait for 5 minutes or more like before. 

Lastly, plug your dishwasher unit into the power socket again.

By following either of these, you should be able to perform the manual reset on your dishwasher. Before loading the dishwasher up with dishes, run a test cycle to ensure it’s working correctly. If there’s no bug, you’re good to go.

Before resetting, check whether the circuit breaker was turned on. Sometimes the dishwasher may not work as the circuit breaker is turned off.

However, you don’t have to perform the manual reset procedure if you just want to reset the cycle. Press the Cancel-Drain or Cancel button. Then you can select your desired cycle.

Keep in mind to fix any leak in your dishwasher beforehand if there is any. Remember to use dishwasher soaps in your dishwasher because ordinary dish soap makes a lot of foamy suds. 

If the dishwasher gets filled with suds, overflow from the dishwasher to the floor will occur. Keep in mind to fix any leak in your dishwasher beforehand if there is any.

Here are some of our recommended dishwashing soaps that you might like:

Product 1
Product 2

Your dishwasher still doesn’t operate accurately even after the manual reset? This is your queue to run the Control Panel Reset to fix the issue.

Method 2: Control Panel Reset

For the control panel reset, you have to press two specific buttons. Each button needs to be pressed five times. You need a total of ten presses to complete the control panel reset. 

Sounds a bit confusing? Don’t worry, we’ll clear it out for you!

Before starting, check if your dishwasher vacuum break is correctly installed. If it is, you’re good to go!

Now, press the Hi-Temp button. Followed by that, press the Heated Dry button. Now repeat this procedure five times. Your dishwasher door must be shut off entirely before performing the control panel reset.

Depending on the model, your dishwasher might have the Hi-Temp Scrub or heating element Wash button. And your unit might have the Energy Saver Dry or Air Dry button instead of the Heated Dry button. 

You need to press the alternate buttons in that scenario.

After doing so, the LEDs above the buttons will start blinking. Then you might hear some self-diagnostic sounds. For example- the sound of the drain pump engaging or other similar activities. 

This self-diagnostic process may last for a few minutes. Leave the dishwasher as it is until it finishes the whole process.

Next, a new cycle needs to be started. To do so, press the Cancel-Drain or Cancel button. This will start the drain pump, and the drain cycle will last for about two minutes.

With this, the control panel reset is finished. Now you can choose the desired cycle according to your needs.

What Should You Do If Your Kitchenaid Dishwasher Still Fails to Reset?

The dishwasher may still not work after running both manual and control panel reset. There might be two probable reasons behind that:

  • The fuse of the dishwasher is blown.
  • Potential complications in the computer board of the control panel.

You can access the fuse and the control panel computer board by removing the door panel. But this is not as easy as closing the space between the countertop and dishwasher

In that case,  call the repairman or the service center to fix your Kitchenaid dishwasher. Unless you’re an expert, we don’t recommend you do that. 

With that, our discussion ends here. We hope resetting the dishwasher solved your problem. But if it doesn’t, call a professional. 


Question: Do Kitchenaid dishwashers have a single reset button?

Answer: No, Kitchenaid dishwashers don’t have one single reset button. You need to press several buttons sequentially for resetting.

Question: Why is water stuck in the bottom of my dishwasher?

Answer: The reason why water is stuck in the bottom of your dishwasher is the clogging of the filter, garbage disposal, drain pump, or air gap. This occurs due to the food and sediment being built up within these systems.

Question: Will vinegar unclog my dishwasher?

Answer: You can try pouring 1 cup of vinegar into the basket, followed by half a cup of baking soda. Wait for 15 minutes, then pour some boiling water. Hopefully, it will clear the clog. 

Last Words

Now everything should be clear to you about kitchenaid dishwasher reset. We hope it helped you to fix your Kitchenaid dishwasher problem.

Make sure to follow through with each step attentively for the best result.

Wish you all the best!