Skip to Content

Kreg Accu-Cut Set Up and Review!

Thinking about making a shelf for your room but confused about the board cutting?

You can’t hire someone just to cut boards for you.

Each time you have to cut a board, it will be costly.

So, invest in an acc-cut, and a circular saw to make your life easier. 

Here you will get the Kreg Accu-cut setup and review.

For the perfect cutout, you need to follow some steps. First, you must fasten the wood and correctly grip the saw. After that, determine the proper depth of the cut. Use the circular saw to draw the cut line. You must utilize the sawhorse and think about the splinters before losing it.

That’s just the beginning. You will get more information in the article. Simply navigate through it to locate everything you require. You will find a review at the end too.

Let’s discuss it right now!

Kreg Accu-Cut Review

Today, I will review the Kreg Accu-cut. Before we start reviewing the product, what is on the packaging? You can see in the packaging that it can do rip cuts, cross cuts, and angle cuts. On the other hand, you can see how long it can be cut. 

It also works with left or right blade saws. In the box, you will find one starting block, a sledge, two aluminum rails, and connectors. There is also a handbook included. When you look at the rails, you’ll notice that they have a sticky touch.

It looks like it will go against the OSB board. If you go back and forth on it, it won’t move. First, you have to attach the rails. You will see arrows on the rails. In that direction, you need to connect them with the help of the connectors.

Make sure you attach those two rails nice and tight and that both slots are even on each side. Now, you need to connect the starting block, pick any sides and attach them. Just slide it into any t-slots. You can cut as many rails as you want to cut big things.

Above I talk about the setup for a straight cut. After following all the instructions, I got a perfect 8-inch cut on every side. It was nice and steady. It didn’t move at all. It has a problem with the sides of the clamps.

But if you follow the instructions perfectly, you are good to go. You can cut laminate or vinyl plank on any board with the Kreg Accu-cut.

How to Set Up the Perfect Straight Cuts

You can set it up for the perfect straight cuts in the next nine steps. Don’t panic while doing it; it’s pretty easy. Here we start!

Step 1. Fasten the Wood

Attaching or securing the timber may focus on the cut rather than the wood.

A circular saw may typically be used to cut wood without fastening it, specifically if you’re comfortable using a circular saw, which is the bulk of the wood. Otherwise, the board you’re cutting makes moving during the cuts very impossible.

It is, therefore, always a good idea to clamp and hold the wood before cutting. It will maintain its level throughout the cut. This helps you to make the most of both saws. And the wood, leading to straighter cuts.

Step 2. Correctly Grip the Saw

There are proper and inappropriate methods for using a circular saw, just as there are many different types. How you hold it will undoubtedly influence how the cut turns out.

Circular saws are classified into two categories. Circular saws, both right and left-handed. Correct circular saws are for right-handed people. At the same time, left-handed circular saws are for left-handed people.

Even though not utilizing your hand type gives you a better view of the cutting blade. Having your hand type allows you to handle it better without your hands crossing over. Don’t remove the loosening bolts.

Step 3. Determine the Proper Depth of Cut

The first step toward a straight and exact cut. With your round saw, determine the proper depth of cut. Even without the appropriate depth of cut, the blade may stray from the straight section. It results in a skewed cut.

Trimming without the correct depth of cut is also harmful. Rake the blade so that it just protrudes a quarter-inch. You’re chopping the bottom of the tree.

Step 4. Use of the Circular Saw Guide

A round saw guide, such as the Kreg rip-cut guidebook, is recommended if you are inexperienced. It’s your best bet for consistently producing straight cuts. You don’t need to measure using a guideline. Also, you don’t even need to create a straight line to designate the cut line.

Do you need to buy a circular saw? Check out these products:

DEWALT 7-1/4-Inch Circular SawThe DEWALT circular saw has lightweight magnesium and aluminum construction, including a durable magnesium footplate. The extra wide saw hook of the corded circular saw accepts materials up to 2-3/4-inch (70mm).
Metabo HPT Circular Saw 7-1/4-InchAn electric brake and 15 Amp Motor Circular Saw can stop the blade from spinning, eliminating unintentional cuts. Its 15 amp motor provides an incredible no-load speed of 6,800 RPM. A new motor design offers up to 40% quicker cutting speed.

People using it with Kreg-Accu saw the most.

A circular saw guideline can assist you in cutting sharp lines with your circular saw. Quickly set the Kreg reg circular saw an approach to the desired width and cut. It’s ideal for straight rip cuts, repeated cuts, and, most importantly, straight cuts each time. You move the circular saw along the slide.

Step 5. Draw a Cut Line

This is the guide if you’re a newbie concerned about making a deformed cut with your circular saw. However, one of the simplest ways to ensure a straight cut is without a saw tip. It is to mark the section of the cut.

Simply draw a simple straight line on the item. You may wish to cut using your speed square or another board with a straight edge. Then, while performing the cut, you may direct your blade down that line. And the resultant component will be as perfect as the row you drew.

Step 6. Utilize a Sawhorse or Workstation

A sawhorse or simple workstation elevates the workpiece off the floor, allowing it to be accessed. Always utilize a sawhorse or a workbench if you have access to one.

It keeps the board you’re sawing at an optimum level, keeping the cuts safer, simpler, and quicker. As a result, your circular saw will be able to create cleaner, smoother cuts.

Step 7. Prevent Splinters

A circular saw operates by rotating the hooked side of the blade. The teeth jut upwards from beneath them into the wood. That means that if you cut the wood against the grain. There will be splinters at the top.

To prevent damaging the positive side of your wood. Constantly cut with the good edge of the board staring down. So that any splinters at the top may be buried when you’ve finished your project.

Step 8. Allow the Circular Saw Blade

This is a critical step to complete before creating any form of cut. Let the blade achieve full speed after depressing the saw trigger. Before establishing contact with the board, you’re sawing.

Otherwise, when it cuts through the wood, the blade will leave a stain on the surface. Let the cutter achieve full speed before making your cut.

Step 9. Security

Cutting straight cuts is vital for creating unique pieces in your workplace or job site, but security is even more essential.

So, follow all circular saw safety requirements and use the necessary protective gear. Such as protective eyewear to shield your eyes from sawdust and debris while working on your projects. You can make floating shelves using this.

FAQs 

How does one go about making a precise cut in wood?

For optimal results, use a miter saw, or a table saw to accomplish this cut. A table saw allows you to cut more significant amounts of wood. Cross-Cutting wood is more difficult on a blade. A band saw is more likely to ignite the borders of the wood or end in rough cuts.

Can a spirit level be used as a straight edge?

To correctly use a spirit level. Place it in the center of a sturdy vertical or horizontal surface. Set a straightedge on top of the plane to be verified. And the set of scales on top of the straightedge.

Why is my miter saw not cutting straight?

There are various possible causes for your miter saw not cutting straight. The blade is deformed, damaged, or improperly placed. The miter saw bevel gauge is misplaced. The miter gauge is out of place.

What exactly is straight line distance?

A straight-line distance is a length recorded using a ruler on a paper map. The straight-line distance does not consider the ground between the two places. It describes the distance a bird travels. Another way is an airplane when flying above the ground between two places.

Wrapping Up

Above I talked about the Kreg Accu-cut saw setup and review. You can set it up by just following those steps. I also added my experience to a review check on that. You won’t be disappointed by the product.

You must always take safety precautions before even attempting to use it. Don’t play with the circular saw blade. And buy a bag for it to store or leave it in a place where kids can’t go!

See you again in the next article. Until then, take care and make beautiful things!