Skip to Content

How to Move Washer And Dryer Hookups [3-Phase Guide]

Home renovation might sound fancy in your Pinterest feed.

But in truth, it’s exhausting and requires months of detailed planning.

This can also involve moving the washer and dryer to another room.

Not knowing how to move the hookups can halt the operation.

How to move washer and dryer hookups?

Before you start the moving operation, you have to carefully plan out the plumbing and electricals. After that, insulate the drywall and create openings for the outlets, drain, and water source. Attach the water supply hoses to the valves and the drain hose to the washing machine.

The answer seems a bit too short? Take a few minutes to finish this detailed article. I’ve described the necessary steps for you.

Relocating Washer And Dryer Hookups

The task of relocating washer-dryer hookups is no joke. It involves weeks of careful planning and expecting the unexpected. You’re bound to bump into several obstacles and have to come up with a lasting solution.

To go through all that, one should be aptly prepared with well-calculated planning. The following guide will help you move your washer and dryer hookups with the least fuss-

Phase 1: Immaculate Planning

In this phase, I’m going to complete all the necessary pre-installation preparations. It’ll help us set up our location and all the plumbing and electrical rerouting.

Step 1: Picking the Spot

The operation begins with choosing the new spot for your washer and dryer hookups. Your location should be easily accessible, soundproof, and have the ideal layout for remodeling.

Step 2: Making the Blueprint

Draw a blueprint taking every possible step and measurement into consideration. The route of the pipes, measurement of distance, appliances, fixtures, everything should be in the blueprint.

Step 3: Moving the Appliances

Pick up the washer and dryer from its previous location to the new location. Cut off all the power sources and drain the faucet lines. 

A utility cart can make the job easier for you to relocate your appliances. If you need a utility cart, you can take a look at our recommendations-

Product-1
Product-2

These utility carts come with multiple trays and have a superior carrying capacity. The ball-bearing casters make them easy to maneuver and carry around.

Phase 2: Setting Up

With the initial planning phase completed, it’s time to set up the site for installation-

Step 1: Scraping off Old Setup

You’ll have to get rid of the old setup to make space for the new one. If you’re renovating your home, you might have to remove your drywall. The pipes and electricals that might come in your way have to be removed.

Cut off the old pipes using a pipe cutter and drain the stagnant water. Chop them low to the ground and cap them off if there’s a water source nearby.

Step 2: Rerouting Plumbing Pipes

Reroute the new pipes according to your initial blueprint to the faucet. Do it in a manner that both the valves get adequate water supply at the same time. Bring the pipes in an opening through the drywall.

Step 3: Establishing Electrical Outlets And Circuits

There should at least be 3 GFCI outlets near your washing machine and dryer. Meaning that 3 circuits for the laundries. There should be a 50-amp breaker circuit solely dedicated to the dryer.

Phase 3: Reinstallation

Now it’s time to reinstall all the appliances to complete the relocation process-

Step 1: Electricity

Start off by setting up the electrical connections. Most washing machines require about 120 volts of electricity. So they can be plugged in with a shared circuit. Be sure that the outlet has ground fault protection.

On the other hand, the electrical requirement of a dryer is 240-volt. A 50 amp dedicated breaker should be designated for your dryer.

You should assign the task of installing the dryer circuit to an electrician.

Step 2: Water Supply

Your washing machine should be placed closer to the faucet. This way, you can tap into the inlet and outlet lines for cold and hot water. 

Connect the hoses to the washer according to the color of the hose. Be careful not to connect the hoses too tightly to the washing machine. Doing so can break the plastic ends.

Take the hoses and connect them to the hot and cold valves.

Step 3: Drainage

Take a hook-shaped drain pipe and connect it to the washing machine. Throw the hooked end into the drain hole. 

If the drain hose is too long, it can overflow and clog the drainage system. Likewise, a shorter drain hose isn’t ideal either.

Washing machines tend to shake a lot while cleaning heavy loads of laundry. This can loosen the drain pipe if there’s not enough slack. Try to buy drain pipes with more slack that’s not too long, but not short either.

Step 4: Dryer Gas and Vent

If you’ve got a gas dryer, you should call for a professional’s help. Install a ½ inch black iron gas line to the gas dryer.

For the dryer vent, clean up the vent before connecting the metal duct pipe. Metal duct pipes usually come with a clamp to screw it tight with the vent. Don’t tighten it too much or it might cause leakage in the pipe. Connect the pipe to the wall vent after that.

Blocked ventilation can cause water leakage from the dryer. Clean the dryer vent properly before installing it.

And with that, the washer-dryer hookup is successfully moved to its new spot. We highly suggest asking for a professional’s help if you’re not comfortable dealing with electrical appliances.

FAQs

Do I need to vent washer dryers?

Answer: Unlike a standard dryer, combo washer-dryers nowadays don’t require to be vented. So you can use the washer-dryer anywhere without a vent with just electricity and water connection.

How is water drained by a washer-dryer?

Answer: The moist air inside the washer-dryer is cooled by the condenser. The moist air cools down and produces water that needs to be drained from the machine. 

How do I clean lint from a washer-dryer?

Answer: A thorough cleaning of the washer-dryer’s interior can clean up the lint. To avoid lint formation, you can apply a touch of white vinegar to your laundry.

Conclusion

Hope this article answered all your questions on how to move washer and dryer hookups.

Be careful while rerouting the electrical circuits. You must designate a dedicated circuit breaker for your dryer and washer.

Keep safe and have a fun time renovating your home!