Skip to Content

How To Paint Cement Statues [Explained]

This article is for informational purposes. Always seek the advice of qualified professionals.

It’s effortless to paint a cement statue. But are you aware of the process? There’s nothing to be disquiet about even if you don’t. Don’t think much. I understand it can be pretty stressful. 

How to paint cement statues?

To paint a cement statue, you have to start with the cleaning. After cleaning, if you find any crack, you have to fix it with epoxy plaster. Time for applying the primary coating. When the primary coat is thoroughly dried, paint the final layer. Lastly, you need to seal the paint.

To complete the process, you’ll need detailed instructions. 

Are you excited? Then continue reading!

Tools You’ll Need

  • Acrylic Paint
  • Brushes
  • Cement Sealer
  • Towel 
  • Bucket
  • Water
  • Dryer

How To Paint Cement Statue: Complete Procedure

You might know the cost to paint a whole room. But you’re under confident enough to paint a statue? You may believe that you must accomplish it under the supervision of professionals. It’ll cost you a lot.

No, you need a few things and should know the techniques. I’ll explain to you all the detailed process here. 3 steps would be enough to paint.

Step 1 of 3: Cleaning 

You have to start with cleaning before painting is necessary because you can’t paint with all the specks of dirt or loose cement. 

To clean the cement statue, you need to take a bucket of tap water. Clean the statue with a brush. You can use a toothbrush to clean the smaller parts. Scrape the figure using plain water. 

You can keep doing this until you’re satisfied with the results.

After it is time for drying the paint, better you put it under sunlight. It’ll take a few moments to dry completely. It depends on the warm air. 

After drying the cement concrete, you may see some cracks. You have to fill all those cracks with epoxy plaster. Make an effort to match the shade of your original statue. 

You can break off into pieces. Do it according to your convenience. It’ll take 3 to 4 hours to dry completely. Give some time and concentrate on making it smooth. You’ll find your preferable epoxy plaster in craft shops. 

Here’s some epoxy plaster recommended for you:

Product 1
Product 2

These are readily available in the market.

Use an electric dryer to dry to set all the plaster. 

Step 2 of 3: Time For Base Coating

Better you pour water on the statue to dye the concrete with the paint. Make the figure moist before applying a topcoat. 

Because concrete is permeable, water will take the paint deeper into the top, making the base coat more durable. 

Prepare a pitcher of freshwater to immerse the figurine with. There is no specific amount of water that you should use on the statue, 

Do it as long as it is entirely drenched.

To ensure that your acrylic primer coat is swallowed up, mix it with water. 

It’s not necessary to add water to the actual paint. When a primary coat is watered down, the cement consumes it and dyes better as a result.

There is no specific water ratio that you should use.

Apply the topcoat to the bottom of the cement statue first. 

Allow the bottom to dry by laying it on its side. Another thing to remember is that this paint has to be the same base coat paint.

Use a 2 inch (5.1 cm) fine paintbrush to apply a primary coat to the whole statue. For the base coat, use acrylic latex exterior paint. While painting there’s a chance that latex paint might fall onto your concrete floor. Be aware of that!

After allowing the basecoat to set for 5 minutes, liquid paint may be felt with your hand. It’s ready for the topcoat if it’s entirely dried. 

Try to use acrylic latex paint on a hot day to your cement statue because of its chemical properties.

Step 3 of 3: The Final Step

Now time for the final coat using the dry-brush technique. First, pour into your desired paint and wipe it off on a piece of paper. So there’s no paint left behind in the brush. 

With that dry brush now paint the cement statue. 

Remove the unnecessary paint after the final coat of paint. You can do this with a paper cloth. 

You have to give enough time to dry the final coat of paint. Approximately, it’ll take 24 hours to dry it thoroughly. Sometimes it can take more—nothing to be worried about. Try to dry it under sunlight. 

After drying the final coat, you can now paint all the details. For detailing, you will use a small brush. 

Sealing the cement statue is one of the essential steps. It’ll make your statue last longer. When applying the sealer, place the cement statue on a concave surface. Let the sealant dry for 24 hours. 

And you’re done with the painting!

Tips And Tricks

Tip 1: De-icing solutions and powerful cleaning chemicals you should not use on your painted cement statue. 

Tip 2: In the winter, don’t put cement statues outside to dry since moisture will accumulate in its pores, leading it to shrink and crack.

Tip 3: When working with epoxy plaster, use gloves to keep your skin from discomfort.

Tip 4: The most used primary coats are black, gray, and brown. You can use these paints too. You can’t use white paint as a primer

Tip 5: Try to avoid spray paint. It won’t look as pleasing as acrylic latex paint. 

Tip 6: To make the statue look shinier, use a can of translucent enamel spray.

You can follow the tips and tricks for a better experience.

FAQs

Question: Paint or stain the cement. Which one is better?

Answer: When correctly applied, the paint will remain for years without cracking or peeling, and it can also be used to conceal faults or patchwork on top of the concrete. On the other hand, acid stain penetrates the pores of the concrete and interacts with its various components.

Question: Which season is best to paint? ‘

Answer: Don’t paint when the weather is dry. The cement statue can catch dirt while the paint is wet. Try to keep the temperature between 45 to 85 degrees Fahrenheit.

Question: What could be the best method to separate old paint from cement statues?

Answer: Power washing or sandblasting are two standard methods for removing paint from concrete. Though acetone is commonly used to remove paint from resin, the strong chemical might harm the statue.

EndNote

Now you know everything about how to paint cement statues. Don’t hesitate while painting the cement statue. 

By following these 3 most straightforward steps, you can paint any cement statue. Try to follow all the procedures carefully. Before beginning the procedure, it’s necessary to read the instructions.

Best of luck with the painting!