Skip to Content

How Do I Take Off And Fill The Drywall Anchor Holes: All in One Guide!

Removing the nails and filling drywall anchor holes look simple.

And this is something that most beginners do. As it seems simple and done by beginners, mistakes are common too. 

Thus, knowing how to do it properly is very important.

How do I fill the drywall anchor holes?

To fill the drywall anchor holes, you first take off all the nails properly. Then take off the anchors that are inside the anchor holes. Once you do that, you then patch up the smaller anchor holes. And finally, you fix the bigger anchor holes of the drywall. You can also redesign the wall after that.

This is the beginning of what we have got here. Read along to cover all the necessary info in detail coming up.

Get started now!

How to Fill The Drywall Anchor Holes?

Filling the drywall anchor holes may look easy. Well, it is actually not that hard actually. But remember you need to know the proper way to do it.

If you fail to follow the steps properly, you may mess up. You would just deteriorate the condition of the drywall. 

Thus, we have got here the steps on how to do it properly. But before you get started, you need a few supplies.

The first thing is the hammer along with a needle tip plier. You also need a hand held hacksaw, a vice grip, and a drywall knife. 

Once you are ready with the equipment, take a look here and get started.

Step 1: Take off All The Nails First

First, you need to take off all the nails. There might be a few of them that might be halfway taken off. 

And you need to take that off before you do something else. To take these loose nails, you may use a screwdriver. 

Just twist off and take the nails pretty easily. Remember this is a basic step even when you want to fix the loose anchors

Working with drywall needs to remove all the nails first.

Step 2: Take off The Anchors

When you take off the nails, you would see the anchors still stuck in the wall. Now, you need to take off the anchors. 

And the thing is you can do it in a number of ways. To do it, you can follow the easiest one first. Take a fresh long nail and put it into the anchor. 

Twist the nails halfway through the anchors. Then pull off the nail holding it tightly. And the anchors from the wall would simply come off. 

If you think it does not work properly, you may also use a hammer. Take a hammer and pull off the nail and the anchor would definitely get off.

In case, you do not have fresh nails, you may use a needle nose tip plier. You insert the plier inside the anchor. And then pull off the anchors. 

In that case, the wall would be a bit damaged. But you can fix it later when you are finishing off the process.

Lastly, you may see some nails that are comparatively bigger. In that case, you would not be able to take those with a plier or hammer.

Take the handheld hacksaw and go back and forth along the nail. Keep moving it back and forth until the nail comes off.

Remember there might be some pins that are really thin and long. For these nails, you can use the vice grip. 

Hold on to the nail and keep moving it to right and left. Do it until the nail slowly comes off. Remember that I recommend using a vice grip only for the long and thin nails.

Step 3: Patch up The Anchor Holes

This time, you need to take your drywall knife. Start rubbing the hole spots in a way so that the drywall is even out. 

Keep moving the knife up and down to take off any leftover or loose debris. You have to make the surface smooth and even. 

Now, take some of your joint compounds in a tiny paint scraper. Then put it onto the anchor holes slowly. You do this to the holes that are about 0.5 inches. 

Put it onto the holes in a way that the holes are filled properly. This joint compound can also fix damaged drywall around the electrical outlet.

You know this compound may be shrinking in a bit of time.

For this, add the compound slowly. And try to make the top of it a bit thicker. As a result, when this dries out, it would even out with the surface. 

This way, you need to fill up all the anchor holes in the drywall. And when you are done, you must scratch the surface gently with the knife. 

Because this would help it to even out the surface even more. Just scrape off anything that gets in the way. 

Now, you may be seeing bubbles on the anchor holes after filling them. But you do not have to worry about that. Because that would sink in once they dry out.

Once they dry off, you need to apply another layer of this joint compound. But make sure the first layer is dried out completely.

The times of drywalls to dry out may vary depending on the size. But you can watch out for it to make sure when it dries out.

Once you have applied the second layer, let it dry too. Wait for the time it takes. And then you need to use sandpaper on the surface to even it further.

Using sandpaper on it would give the surface the final smooth plane. You may think it is not that important to use sandpaper for this.

But remember that it is one of the most important parts of this. Sanding is really needed because it eliminates the tiniest debris or dust particles off the surface.

As a result, this finishes off the final outcome of the drywall surface.

Step 4: Fix The Bigger Holes

This time you need to look at the bigger holes. To fix these, you need to use mesh tape. Take the tape and lay it on the hole accordingly. 

But if you do not have mesh tape with you, get one. Take a look here to count on our products:

Product 1
Product 2

Hope this helps!

Coming back to the point-

After that, you put a joint compound on the mesh tape to cover it up. Wait for a while until you start putting on the second and the third layer.

Yes, you have to go for the third layer too. This would bury the grid lines of the tape. Once you have covered it up, let it dry.

Following that, you need to sand the area to smooth it off. And finally, you have successfully filled the drywall anchor holes!

Remember that mesh tape can also come in handy fixing baseboard and drywall gaps.

Now, your drywall is ready for other uses. Like, if you want, you may put up texture or any design on the wall now. 

And this may even be better for your anchor holes to not seem noticeable anyway. Good luck!

Additional Tips for Drywall Anchor Holes Refill

Last but least, I have got a few tips for you. Take a look:

  • Once you refill the drywall anchor holes, try to utilize the space. That means if you can then get a painting on that. It would look even better.
  • Make sure you keep the wall clean every time.
  • You may consider repainting that particular area which is not a must though.

FAQs

Can I put different types of nails to fill the anchor holes?

No, you can not directly put in different types of nails to fill the anchor holes. You need to go with the specific type due to the size left there. But if you still want to do it then you need to tune the size of the holes. But that is not really necessary unless it is too special or really needed.

Is it time-consuming to remove and fill the drywall anchor holes?

Yes, it takes a bit of time to complete this task actually. But it is not actually time-consuming. Because it does not take as long as you may expect it to. And if you are especially someone who has done it before, it would take very less. On average, it may take a few hours to complete this operation.

Does the drywall spoil over time if I don’t refill the holes?

Yes, the drywall may be damaged over time if you do not refill the holes. It is not a must. But there would be the possibility of the drywall being damaged over time. In order to prevent this, you can either refill the wall or put nails into the holes. But keeping them like that would look really odd.

The Final Words

Now you know how to take off and fill the drywall anchor holes! We believe you have now no more confusion regarding this.

But remember one thing. Do not take off nails from the drywall too often. Although you may refill the holes this would still have an effect. These may put up marks if you do it too often.

All the best with your work!