Have you noticed soot in your favorite metal objects? It may make you very embracing then. But don’t worry, I may have two excellent alternatives to address your situation!
How to remove soot from metal?
There are 2 different approaches you might use to fix the problem. Firstly you can use the Soap-Water-Vinegar 5 steps method. If it doesn’t work you can use the Soda-Lemon-Hydrogen Peroxide method then. We mention the methods by difficulty level. By applying one after another you can get rid of the problem.
Here’s a quick rundown. I’ve included all of the specifics in the step-by-step instructions below. So, why not go deep? Let’s go!
Method 1: Soap Water Vinegar Method
- Dishwashing liquid
- Dish Soap
- Scrubbing sponge
- Hot water
- Spray bottle
- Hand gloves
- White vinegar
- Scrub brush
- Dry rag
You can purchase the best spray bottles needed, from these recommended products below:
They are the greatest in the market. You can now utilize them without concern.
Step 1 of 5: Mix Dish Liquid with Hot Water
Put a few drops of dishwashing liquid in a bucket of boiling water. Dish soap or zote soap aids in the removal of soot from metal by breaking it up.
Step 2 of 5: Dip Scrubbing Sponge & Scrape
Scrape the soot deposits back and forth with a scouring sponge dipped in soapy water. The bulk of the soot from the metallic surface is removed this way.
Step 3 of 5: Spray Vinegar-Water mixture
Spray directly into the soot deposits with a half part warm water solution and half part white vinegar mixed in a spray bottle. White vinegar is somewhat acidic, which aids in breaking up the soot and properly cleaning the metal.
Step 4 of 5: Run Scrub Brush
To remove any stubborn soot from the metal, use a nylon scrub brush. Use a plastic scrub brush instead of a metal scrub brush to avoid scratches.
Step 5 of 5: Dry The Metal
To get rid of leftover soap and vinegar, clean the metal with a wet towel and then dry it with a non wet towel.
Method 2: Soda Lemon Hydrogen Peroxide TSP Method
- Hydrogen peroxide
- Kitchen Baking soda
- Carbonated water
- Bristle brush
- Trisodium Phosphate (TSP)
- Phosphoric Acid
You can get all of the resources you’ll need from the goods listed below:
Step 1 of 6: Try Carbonated Water
To dissolve soot, use carbonated water. Carbonic acid, which is found in carbonated beverages, can help to reduce soot deposits.
Step 2 of 6: Use Salt & Lemon Mixture
Squeeze lemon or lime juice over soot and sprinkle table salt brine on top. Allow the mixture to sit on the metal for two to three hours. Then scrub it off with the lemon.
Step 3 of 6: Apply Tartar Soda Hydrogen Peroxide Paste
Make a paste of 1 teaspoon cream of tartar with 1 cup of Borax or baking soda, and enough hydrogen peroxide. Allow 30 minutes to dry after applying this paste to the soot area. Use a wet towel. Clean the surface. If required, repeat the process.
Step 4 of 6: Spray & Scrub Vinegar
Allow the acetic acid in white vinegar to dissolve the soot by soaking or spraying it on the sooted region. Your spray bottle trigger sometimes can jam off for vinegar, you can fix the spray bottle trigger in a minute.
Then, Scrub the area with a pad or brush. Then add more vinegar. Leave it for 30 minutes. Clean with a wet cloth and repeat.
Step 5 of 6: Apply Borax Lemon thick paste
To make a thick paste, combine Borax and lemon juice. Apply to the dirty area and leave it there for half an hour. Using a scouring pad or steel wool, scrub the corroded area. As needed, repeat the process.
Step 6 of 6: Apply TSP & Scrub
Combine 1/2 cup trisodium phosphate and 1/2 gallon warm water in a mixing bowl. Allow 15 to 20 minutes for the corroded area to soak. As needed, scrub the afflicted area with a bristle brush.
Precautions need to follow
- Wearing goggles, gloves and a mask
- Take care using hydrochloric acid
- Measure perfectly of mixture
- Cover or cap the solution bottle and keep it in a safe location
Question: Can I use sandpaper to remove soot from metal?
Answer: Sandpaper is an excellent soot-removal tool. However, there are many grit sandpapers to use. You can use 320 to 400 grit which is the most acceptable one.
Question: Is there any possibility of a leak in metal?
Answer: It will depend on your object’s thickness. If it is a thinner one, be careful with your mixture and acid use! It can be leaked because of the high power of acid. But if it is a thicker one there is very very little chance to leek.
Question: What should do if the mixture is not measured properly?
Answer: You should be very careful to make the mixture. But if it still happens then you should maintain the ratio of the mixture. It will also work as the perfect one.
Now you know how to remove soot from metal. I guess you have no confusion with the process anymore because it is an easy one!
I hope you find this article to be quite helpful.
Say bye to your soot forever!