Skip to Content

How to Repair Concrete Steps Pulling Away from the House In Just 6 Simple Steps!

Are your house concrete steps pulling away? And you have no clue how to solve that. Well, we have the right solution for you.

How to repair concrete steps pulling away from the house?

Firstly, to repair the concrete steps you have to clean the surface area properly. Use a wire brush to remove all the dirt. Then, you have to examine the adhesive areas. Now mix the concrete with the required elements and apply it. Let it be hardened for some time. Give it a smooth finishing!

We’ve got the full guidelines down below. Like the overview you see? Great then! Dive in and find out all of it!

How to Repair Concrete Steps

Whenever a concrete step starts to detach from the pavement, it is usually due to excessive pressure or drastic moisture fluctuations.

 These sections may usually be repaired with a strong concrete patch and a protective sealer to help prevent further separation.

Let’s start the process. Without any further ado.

Step 1: Cleaning

Before starting working with the concrete steps, you have to clean the surface area properly.

Clean the affected areas with a stiff brush to remove any loose dirt or debris.

Debris and grime can become stuck in the space between your steps and the home, producing a huge annoyance. 

Though it’s not similar to removing studs behind aluminum. 

Depending on the extent of the distance, you might have to utilize a vacuum with both drying and wet capabilities.

Loosened concrete fragments away quickly. Use a hammer and a chisel to clean this loosened concrete. Before mending, the surface has to be totally clean.

You can purchase your desired cleaning tools from these recommended products below:

Product 1
Product 2 

These are the best ones in the market. And you can use this without any worries!

Step 2: Bonding

Examine the area where the concrete stairs are separating from the house.

In order to restore the steps, you must use concrete bonding. Put the bonding adhesive with a brush to the gaps or damaged area that demands care.

Before proceeding to the next step, look at the label of the bonding adhesive to determine the required cure time.

Concrete bonding glue cure periods vary by manufacturer and should not take more than 10-25 minutes. 

When the adhesive has fully set, you can proceed to the following step and finish the repair.

Step 3: Mixing

It’s now time to make a pack of fast concrete to fix your steps.

Hold 2 containers, a drill or trowel, a pack of concrete, safety gloves & eye protection.

You must have all of your stuff gathered and ready to go since the concrete hardens quickly and you won’t have time to rush about.

Put the concrete inside an empty container after opening the bag.

To loosen the concrete mix, agitate and stir it with a trowel or drill. Fill a second bucket halfway with cold water & gradually put it inside the container containing the concrete.

Make liberal use of cold water, since utilizing less can result in thicker, stronger concrete. 

When your concrete mix has reached the consistency you like, it is then ready to be placed.

Step 4: Applying the Concrete

Bring your pail of concrete around to the steps & prepare a trowel. 

Your concrete bonding glue should have been set by now, ensuring that the concrete adheres to the steps. 

Approach the distance between the concrete stairs and your house and start putting the concrete down.

Each of the layers of concrete must be thin, and you may continue the procedure until it’s completely filled. 

Work fast so the concrete remains workable while being applied with the trowel.

Step 5: Rebuild the Steps

Switch through the mix and the mending material while applying the concrete. 

The patch should also be applied thinly enough that it adheres both to the adhesive and the concrete mix. 

Switch between the scooped and smooth edges of the trowel to ensure that the patch & concrete settle equally on the steps.

Both the patchwork and the concrete should be uniform so neither element stands out.

If needed, seal the concrete steps so the rain can’t damage them. The last thing you might want is to dry the materials unevenly, which would be bad for both structural and cosmetic reasons.

Step 6: Lasting Details

Using a rubber float, smooth and integrate the edges of the fresh concrete and repair.

If there are any discrepancies, go over them again with the flat side of the trowel.

Check the weather forecast to determine whether there will be rain or excessive humidity and if so, cover the drying concrete with plastic.

Allow 24 to 48 hours for the concrete to dry and repair to thoroughly cure before touching them again. 

In case you have used plastic wrap, then you may remove it and seal the fresh concrete and steps overall.

 If you have water leakage or any water pipe around the steps, it is recommended to add a flashing between the concrete steps.

You are now finished, and your concrete stairs would no longer appear to peel away from the house. It’s critical to note that, while this remedy works, your actions might still be an indicator of foundation issues. 

If this is the case, you should seek the assistance of an expert to assure that foundational damage does not reoccur.

FAQs

Question: How do you repair a house’s loose concrete steps?

Answer: Concrete Adhesion Examine the area where the concrete stairs are separating from the house. In order to restore the steps, you must use concrete bonding. Add the bonding adhesive with a brush to the gaps or broken areas that demand fixing.

Question: How long would it take to fix a damaged concrete step?

Answer: You can fix the surface of a step using a plain trowel within twenty minutes as cement generally hardens in ten minutes, then put an additional mixture to the base of a step in another next 20 minutes when you’re using a sack of “cement all,” which costs six times as much as concrete. A step may be repaired in one hour. 

Question: What do you do to bridge the gap between the concrete stairs and the house?

Answer: You must first clear the space among the steps as well as the house before applying concrete bonding. After the bonding has dried, you would add concrete and use a trowel to fill the gap. Alternate between applying patching and concrete, smoothing it out, applying a sealer, and waiting 24-48 hours for everything to cure.

EndNote

I hope this information has been useful. For you to find out how to repair concrete steps pulling away from the house. We’ll say our goodbyes here.

If you encounter any issues, you can contact an expert. Best wishes for trying out this innovative method.

Sayonara!