Skip to Content

How to Sand Plywood [5 Simple Steps]

Sanding plywood doesn’t need much longer. The process for sanding plywood is simple but repetitive.

The steps require less effort to execute so bear it in mind. 

All you need is some necessary tools for sanding. Now you are good to go. 

How to sand plywood?

First, you need to clean the surface. Then you have to apply sand. Then clean the sanded area and repeat. Try to smoothen the surface and lastly finish off dusting the residue on the surface. And you are done!

Sounds fun, doesn’t it? It is very fun to achieve, although there is more to it. You have to follow certain measurements. Let’s see how it’s done!

Process of Sanding Plywood

Plywood needs the same sanding process like any other hardwood or softwood. This is good news. Sanding wood surfaces is necessary for achieving a smooth and even paint finish. You can also use a self-leveling mixture on plywood.

Keep one thing in mind when painting or staining it. As it might get difficult for getting a brush to evenly coat rough wood. 

Attempting to apply any form of finish on rough lumber can get a sloppy outcome.

The process of sanding the plywood is very simple. It is done in the following five or six consecutive steps. 

So let’s see the process of sanding, it won’t take long to furnish the house.

So the process of sanding starts with cleaning the surface of the wood. Having the mindset, let’s dive into the process of how it is done.

Step 1: Cleaning the Surface

Try wiping away dirt and dusting on the worked surface. A little damp cloth can be used. You may also use your gleaming vacuum. Drive dirt and dust straight into the vacuum bag.

Step 2: Sand the Plywood

Using the 180 grit sandpaper, sand the plywood in a light manner. Because the 180 grit sandpaper is the toughest, do this slowly. 

Make sure you’re working with the grain of the wood. Apply it gently to the plywood as well.

Sand the entire surface no more than three times for best results. This will reveal the grooves and allow you to peel the plywood’s edges. 

Although if it’s for woods to stick thin-set, this has to be done differently. 

Step 3: Repeat the Process

Continue the sanding operation with 200 grit sandpaper. This time, use the 200 grit sandpaper to finish the job.It’s ideal to go over the surface three to four times this time. 

The defects exposed by the 180 grit sandpaper will be removed.

Step 4: Smooth the Board

Using 220 grit sandpaper, lightly sand the plywood. Finally, sand the board using 220 grit sandpaper to make it smooth. Double-check the peripheral. 

After this process, the plywood is said to have been sanded smooth.

Step 5: Remove And Clean the Dust

Slowly try removing any sanding dust that has accumulated. To get rid of more than simply dust specks, a vacuum is your best bet. 

In an alternative way, wipe away all the dust. Using a clean towel soaked in paint thinner rather than your hands. A portable oscillating tool can also be used.

It is done with a sanding accessory instead of your sanding block.

Optional Technique

Envirotex is a material that has been utilized in the manufacture of bar tops. It is another alternate option. Envirotex is an epoxy resin. It helps in curing in about 8 hours at room temperature. 

It leaves a thick, firm, lustrous compound that reaches its full hardness after 48 hours. It also doesn’t require any polishing to achieve its maximum sheen. 

Here are product recommendations for Envirotex for obtaining two kinds of finishing:

Product 1
Product 2

So this becomes a product worth highlighting. 

The identical step-by-step technique for preparing the plywood for polyurethane application would apply. 

But, Envirotex would be used instead of polyurethane.Now you have applied the finishing touches. 

But as you finish it, something else takes your interest. 

If these are woods used to make your houses, you want to make house woods fireproof. This will be a topic to discuss some other day. 

Until then, I hope today’s query was solved. 

FAQs

Question: Can you stain plywood?

Answer: Staining plywood is comparable to the process to stain wood. When utilizing, however, special caution should be exercised. To prevent sanding through the top layer, especially during preparation. And it is to be done to stain the plywood edges properly.

Question: Is it better to paint plywood or stain it?

Answer: Plywood can be painted or stained. It makes no difference while doing any of these. But, as you descend in grade, the terrain becomes rougher. So it requires more work, in addition to the material’s quality deteriorating.

Question: What is the best plywood finish?

Answer: Polyurethane varnish is arguably one of the most commonly used finishes on plywood projects. Especially when it comes to furniture made of hardwood plywood. Polyurethane is a simple material to deal with. With minimal effort, it achieves a high-quality finish.

Conclusion

There you have it! How to sand plywood? The question has been answered. Now, you can ease your mind as you know the process. 

All you need now is a little bit of confidence and patience, and you’ll be OK.I hope the article sparked a little confidence in you.

I hope everything goes according to your plan while enjoying the process!