Skip to Content

Move Strike Plate To Fill Hole: A Step-by-Step Guide

Sometimes, you can have basic problems like the door latch not lining up with the strike plate. This happens when the previous screw hole gets eroded. By filling up the screw hole, you can resolve this problem smoothly.

How to fix the move strike plate to fill hole?

Door latch and strike plate not lining up is a fairly common problem. To resolve this issue, all you have to do is fill the gap that was created when you moved the  plate. You can use wood filler or wood epoxy to fill the screw hole gaps and make an even surface. Leaving the gaps won’t look nice on your doorway.

Let’s make your doorway look good as new!

What You’ll Need

To fill up the holes, you’ll surely need some necessary items. Without them, you’ll not be able to operate your desired plan. So, here’s the list of items that you’ll need:

  • Chisel 
  • Wood filler/ wood epoxy 
  • Paint brush 
  • Sandpaper 
  • Plastic scraper/ putty knife 

Now that you have everything you need, let’s dive into the process. 

Filling Up The Holes: Step-by-Step Guide 

When guests show up, first impressions are always important.. Marks from replacing a strike plate are displeasing in any entryway. Although you can repair it in three simple steps so that no one will ever notice. 

Step 1 of 3: Clean Up The Hole 

Before operating on something, you first need to clean the mess around the area. If you miss this step, the product you’re going to use won’t stay there for longer. You’ll have to go all over the process once again:

  • You must clean splinters and faulty paint if there’s any from the hole with a chisel.  
  • From the surrounding area, remove all the other scrap as well. 
  • Keep clothes under where you’re working. It’ll keep the area less messy.
  • To varnish the surface, make use of a grit sandpaper. We recommend you to use 180 grit sandpaper. This’ll allow the wood filler and the paint to adhere to the surface.

Step 2 of 3: Filling The Chamber 

After cleaning the mess you had in the hole, now you need to dive into the main work. This step needs the most patience and focus:

  • Fill up holes with the help of a plastic scraper or a  putty knife. It needs to be filled up with wood fillers. You can also use epoxy instead of wood fillers. This will give you an airtight seal, like glueing pennies to wood
  • Make an effort to keep the surface even as much as you can while packing it tightly. To achieve a smooth surface, you can sand the filler using a sanding block.

Here are some affordable sanding blocks you can find in the market:      

Product 1
Product 2 
  • Remember to use extra filler if it’s a big hole. As the filler will diminish as soon as it dries. 
  • The wood filler you put in could take even one day to dry. It depends on the size of the holes you’re filling.

Step 3 of 3: Painting The Afflicted Area 

You need to make sure your product fits in the hole. It can diminish after it dries. In that case, follow the below guidance:

  • Don’t worry if the wood filler you put in shrinks.. It happens in large wood screw holes as well as in composite deck screw holes. Keep in mind which type of screw you use before you put in a second layer of paint. 
  • Another solution to stop the shrunk is to paint the area. Isolate the area and then cover it with a drop cloth. 
  • Brush up around the hole with leftover original paint.

Extra Tips

Now that you have your doorway problem fixed,  you can look for some tips to secure it more.

Tip 1: Using Epoxy Solution 

To seal wood, some epoxy solutions need an epoxy primer. Check the product label for recommended primers. You also must check if the old masking tape is removed. Otherwise it won’t be sealed properly. 

Tip 2: Variation In Colour 

Varieties of epoxy filler are available in the market. They are used on wood, stone, plaster, and other architectural materials. You can also find a variety of colour options as well.

Tip 3: Use Colourants Or Polyester Fillers 

Using colourants in wood to stain and varnish rather than paint is a wise decision. For holes to fill up in steel door frames, you can use specific metal polyester fillers or a solid cover plate.

Things To Keep In Mind

You now know all the processes and solutions for this issue. But there are some things you need to keep in mind. Especially if you’re using epoxy wood resin. Let’s go through them:

  • Epoxy odors are uncomfortable, and also the compounds may have skin-irritating elements. So, when working with epoxy resins, make sure there’s enough ventilation and that you’re wearing protective gloves. 
  • When operating on this project, mix as much as you can use in the time allotted in the product’s guidelines.It should take five to twenty minutes at most. When the resin and solvent combine, epoxy heats up and the chemical changes on its own. 

It may become hard to manage. So,you need to be very careful on this matter. 

That’s all we have to get you out of this scenario. 

FAQs 

Question: How do you fill a striker plate hole?

Answer: Put some water putty on a plate and mix it.Fill up the space and try to get in all the areas.Remove the excess and wait for it to dry to get a flat edge.    

Question: How do you fill a door jamb hole?

Answer: Cut a piece of door jamb out.Then glue on a patch of matching wood. That’s the closest you can go to make your strike cavity go away. 

Question: How do you make a strike plate hole bigger?

Answer: The striking plate can move up and down along with in and out. Expand the strike plate using a sharp chisel. After placing the strike plate, hold it and drill hole with a 1/16 inch screw. 

Conclusion

We tried to explain the solution about move strike plate fill hole. Hopefully this’ll help you resolve your strike plate problem along with your door lock. 

If you get in any trouble while operating on this project, it’s safe to call for a helping hand. 

Till next time, keep up the woodwork!