Skip to Content

10 Steps to Wiring Two Single Pole Switches!

Building two single pole switches on your own for the first time is kind of difficult. You will have to be cautious all the time and follow specific steps to complete it. If you are good at electrical devices, then it will be an easy-peasy process for you. 

Do you want to learn how to wire two single pole switches?

First, you have to install enough electrical boxes to house the lights and switches. Then, using a 14-gauge electrical cable, link each switch to the light it controls. After that, connect the cables to the light fixtures. Push the opposite end of each cable through the electrical box’s back door.

Have you got all your answers with this short description? I guess the answer is no! I’ll go over everything you need and all the required actions in the sections below. Additionally, you’ll discover some advice and safety measures. 

Okay, let’s get started!

Two Single Pole Switches

It is not unusual to connect one, two, or more lights to the same power source. In actuality, it is customary. The primary electrical panel’s circuit breaker is frequently the source. Additionally, it must have a rating high enough to run the lights. 

The switches can be installed in the same or distinct electrical boxes. However, the latter requires the additional job of installing a circuit cable between the boxes. The hot wire in the circuit cable is kept continuous by constructing pigtails. 

Things We Need to Wire Two Single Poles

You need a lot of things to install these wires so that you can do it easily. Here I will mention each and every single thing to complete the process. Let’s see what we need: 

  1. Wire Connectors (36 pieces)
  2. Wire Connectors (78 pieces)
  3. Voltage Detector With LED
  4. Wire Pusher/Puller/Bender 
  5. 2-In-1 Insulated Screwdriver Switchblade 
  6. Long-Nose Pliers 
  7. Wire Strippers 
  8. 15 Amp Single Pole Switch (5 Pack) 
  9. Switch Cover 
  10. Double Gang Electrical Box (Adjustable Old Work)
  11. Double Gang Electrical Box (New Work)
  12. 14/2 Cable, 2 Wire W/ Ground (50 & 250 Feet)  
  13. 14/3 Cable 3 Wire W/ Ground (100 Feet)
  14. Nail Plate Wire Shield
  15. 1/2” Cable Staples
  16. 3/4” Spade Bit (6”)
  17. 3/4” Spade Bit (16”)
  18. Cable Puller 
  19. Black Electrical Tape 
  20. Drywall Saw 
  21. DeWalt Cordless Drill Combo

10 Steps to Wiring Two Single Pole Switches Inside Two Gang J-Box to a Light Fixture!

When you start making two single pole switches, you need to follow some steps. You must be able to repair switches and outlets. The sequence of these steps must be followed. I will thus go into depth about each of the 11 phases here. Let’s get right to  those steps without wasting any more time. 

Step 1: Setup Electrical Boxes

Set up suitable electrical boxes for the switches and lights. The switches can be mounted in separate places. So, each in a single-gang electrical box, or each side by side of a dual-gang electrical box. A rough-in box can be fastened to either a stud or a rafter. For each fixture and switch, or installing a rebuilding box on the drywall.

Step 2: Connect the Switches

Connect each switch to the light it controls with a 14-gauge electrical cable. One end of each cable should be pulled through the backlight fixture electrical boxes. Each cable should have both ends stripped. Because the wires separated, and the last 1/2 inch of insulation was removed. 

You need a 14-gauge electrical cable to complete all the processes. So, here are some excellent product recommendations for you:

 Southwire 55669023 Primary Wire, 14-Gauge Bulk Spool, 100-FeetA 100-foot length of single-strand main wire. It is a 14-gauge white wire. The PVC outer jacket is resistant to water, oil, chemicals, and abrasion. It is appropriate for undertakings involving automobiles, trucks, and watercraft. 
 Ancor 155010 Marine Grade Electrical Round Tinned Boat Mast Cable (14-Gauge, 100-Feet)This 14-gauge is really good but costs a little more. Package Height Of The Item Is 10.0″. Package Length Of The Item Is 10.75″. Package Width Of The Item Is 10.75″

Most people use these cables to complete these steps. I am assuring you that it won’t disappoint you. 

Step 3: Connect to the Light Fixtures

The necessary cable lines should be connected to the light fixtures with black, white, and ground wires. Likewise, connect the black and white wires. Use pliers to spin the wires you’re connecting, then put a wire cover on each set.

Step 4: Push the cable into the Electrical Box 

Each cable’s other end should be pushed through the electrical box’s back to the switch it controls. Once there, remove the cable’s end and separate the wires using a knife. The black wire should have its 1/2-inch shielding removed. It must also be placed into the bottom bronze terminal of the switch.

Step 5: Switched Off the Power

Make sure the power is switched off. Also, the cable is dead before removing the 14-gauge wire from the power supply. Strip the wires after passing them through the rear of one of the switch boxes. It is vital to understand how to replace the outlets

Step 6: Disconnected the Wires

A second 14-gauge cable should have all of its wires disconnected. It will run from the first to the second switch. A second 14-gauge cable should have all of its wires disconnected. It will run from the first to the second switch. All of the wires on a second 14-gauge cable should be unplugged. It will run from the first to the second switch. You can skip this step if the switches are installed in the same electrical box.

Step 7: Cut Up the Spare Cable 

With a tool knife, and cut up a 6-inch section of spare cable. Then carefully remove the black and bare wires. The black wire’s insulation should be stripped by 1/2 inch from both ends. Prepare two black cables if you’ve installed two switches in the same electrical box.

Step 8: Connect to the First Switch 

Connect the top connection of the first switch to one end of the 6-inch cable. Connect the cable’s other end to the black wires using a tie. The one which is coming from the entrance electrical cable. To create a pigtail, that wire will be sent to the second switch. Wrap a wire cap around the pigtail’s end.

Step 9: Second Switch with Different Electrical Box

Unless the second switch is in a different electrical box.  The top socket of the first switch should receive the other 6-inch wire. The pigtail in this illustration will have three black wires. Two 6-inch cables from the switches and one circuit wire.

Step 10: Ground Wires

With the ground wires, make a similar pigtail. The green ground terminal must be connected to the 6-inch length of wire. The other end should be twisted around the box’s three exposed wires. Unless they are both placed in the same box. The ground wires should then be braided using one 6-inch wire and the remaining two together.

Before Starting To Wire A Light Switch

In a domestic environment, electrical power enters the residence and is routed by a service panel. This panel is made up of separate breakers that direct power to various circuits. 

At the service panel, all circuits begin, and they go down cables to outlets and switches. then circle back to the control panel. 

Within the cables, there are wires that perform a variety of tasks. Some lines deliver power to the switches. While others deliver electricity back to the control panel. Others serve as safety devices, reducing the risk of electrical shock.

The best part is that replacing a light switch does not require complex wiring knowledge. Simply unplug the wires from the old switch. Then connect them to the new switch in the same way.

Precautions for Light Switch Wiring Safety

When it comes to wiring, the safest rule of thumb is to avoid dealing with electric wires. If you don’t feel confident in doing so. Because you’re working with cables that have already been properly installed. Also, changing a light switch is typically safe and low-risk if you take the proper steps. 

However, DIYers should not attempt to run new wiring themselves; it is the duty of an electrician. The procedures below will assist you in replacing outdated switches. You may, however, replace them with new ones to improve their appearance and usefulness. 

FAQs 

On a single pole switch, does it make a difference which wire goes where?

A single-pole switch’s wires can be switched. Which wire is attached to which screw terminal is unimportant. A metal channel inside the button closes and opens. If the switch is switched on to block electricity flow.

Daisy wires, are they parallel or series?

Despite being commonly referred to as a “daisy chain,” the speakers are really linked in parallel. The impact is the same as connecting each speaker to the output directly. Furthermore, while connecting speakers in parallel, the overall impedance load of the speakers are lower.

What amperage does a 15 amp breaker trip at?

Most domestic circuits are rated at either 15 amps or 20 amps. It’s important to remember circuit breakers can only handle about 80% of their entire current. This means that a 15-amp circuit breaker can manage about 12 amps. A 20-amp circuit breaker, on the other hand, can handle around 16 amps.

A 20 amp circuit may have how many receptacles?

The solution is 10 outlets on a 20 amp circuit. Follow the 80% circuit and breaker load rule at all times, with a maximum load of 1.5 amps per receptacle. To minimize overheating and electrical risks, make sure your circuit, wire diameter, and outlets are all suitable.

Bottom Line 

Here I cover all the steps to wire two single pole switches. If the electricity to the lights is already connected, ensure that the power is turned off. 

Use a voltage tester to verify the cable wires if you’re unsure. Working with live wires might result in a lethal electrical shock. You have to make sure of some things. If you complete those steps with precautions, you will be good to go!

Ok, bye for now. See you later!