How To Make Wood Stairs Non Slip: 4 Simple Solutions

We may get commissions for purchases made through links in this post.

Everyone likes wooden stairs. Well, why not? They’re easy to clean and add aristocracy to the interior of your house. But so raises a problem – they are slippery. And so you might fall off.

How to make wood stairs non-slip?

When it comes to making wooden stairs non-slippery, there’re a lot of ways to do it. You can just install carpets from top to bottom of your staircase. Or, you can use anti-slip strips on each stair. You can also use anti-slip liquids. And add non-slip components while you paint in the first place.

As we said, there’re a lot of ways to do it. But there are pros and cons to all methods. We have tried to include everything in this article.

Let’s not delay anymore and get started!

4 Ways To Make Wood Stairs Non-Slippery

There can be various ways to make your stairs non-slippery. We have come up with four of the most suitable and most efficient to do this.

Installing Carpet

Installing carpet is one of the most frequent ways to make stairwells less slippery. Carpet adds traction to the exterior of your stairs. At the same time, it may also be a nice touch to the decoration of your house.

You have two choices when it comes to carpet- stair non-slip carpets or carpet stair treads.

Stair Runners

Stair runners are carpet bits that cover the width of your stairs. But do not cross the whole width of each one. Stair runners have the following benefits-

They cover not only the breadth but also the whole depth of each stair tread. They preserve the wood from deterioration. They minimize noise, they look beautiful, and they make your stairs less slippery.

Carpet Stair Treads

Carpet stair treads are another choice if you want to go with carpet. Carpet stair treads are individual carpet pieces that may be placed on each step individually. Don’t worry, carpets don’t harm wooden surfaces. Just like they don’t harm tiled surfaces.

The advantage of carpet stair treads over stair runners is that they are simple to install. The fundamental stages are as follows-

Each step should be carefully cleaned. Measure the stairwell to make sure they’re in the right spot. To hold the treads in position, use carpet tape. Use one part for each surface of the tread or non-skid carpet mats. Then, carefully push down on the treads until they are thoroughly attached to each step.

Carpet treads are less costly than carpeting and are considerably easier to maintain than carpeting. You may easily remove them. Or, clean the wood below and scrub or soak the treads in soap and water. Most significantly, carpet tread fibres offer grip and minimize the danger of slipping. But the catch is to place them appropriately.

Because they don’t wrap around each stair. They don’t supply as much stability as a carpet runner. Cleaning them can be challenging. If you don’t install them properly, they might slip and do more harm than they prevent.

If you decide to go with carpet, be sure to choose a low-pile carpet. Whether for a stair runner or stair treads, install it properly.

Higher carpets have a tripping hazard that will certainly cause more injury than good. If you don’t properly install your carpet, it will slip or bunch up. And cause the same problems you’re wanting to avoid.

Using Anti-Slip Adhesive Stair Treads/Strips

Look down the next time you’re in a business building’s stairway. To avoid sliding, thick black grip tape will most likely be applied to each stair. Today’s transparent anti-slip strips are manufactured using non-toxic materials that don’t contain any kind of PVC.

This sort of adhesive tread would definitely make your stairs safer. But we don’t recommend using it for your house. 

On wood stairs, the black tape would be unattractive. And commercial treads have a harsh sandpaper-like texture that would irritate your feet.

Many companies, nowadays, produce transparent anti-slip adhesive treads for home usage. Here’re a few of our suggestions-

Product 1
Product 2

These products are best in their line according to customer reviews. Simply roll the adhesive end of the treads over each step to install.

By adding a small roughness to the surface of each step, these anti-slip treads successfully prevent slips. The feel is firm enough to prevent slipping yet soft enough to wear barefoot. They’re translucent and hard to spot unless you’re actively looking for them.

One of the finest features of anti-slip adhesive treads is how quick and easy they are to install.

Simply eliminate the paper from the end of the tread. Position the treads approximately one inch from the stair’s edge. And level out any air bubbles utilising the provided roller.

Adhesive Stair treads have plenty of disadvantages.

To begin with, they might be challenging to install exactly straight. You might be bothered that you can’t put them exactly where you want them. It’s hard to keep a straight line when you have to reel them onto each stair from one surface to the other. 

Second, because wood stairs have inherent irregularities and fissures, air bubbles are inevitable. 

Finally, removing them from your stairwell may result in small property damage. Some consumers have complained that they leave a small residue that must be scrubbed away. Others lament the peeling paint on their stairwells. You should be OK if you have standard stained wood flooring. But if your stairs are painted, you should dodge this.

Applying Anti-Slip Floor Finish On The Stairs

Anti-slip floor finishes are liquids that you may use to make your wood steps less slippery. And for curve framed stairs, carpeting is more difficult. So using an anti-slip floor finish is a great choice. If you don’t want to ruin the beauty of your staircase by installing carpet. Or if you don’t want to deal with the small difficulties that clear adhesive stair treads bring. 

Paint or clear coatings are used to create anti-slip floor surfaces. Tiny particles are mixed with the coating to increase friction on the wood’s surface. Although they are not visible to our eyes.

The major benefit is that you may achieve your aim of making your steps less slick. And without compromising the natural beauty of hardwoods. There are a few drawbacks to adopting an anti-slip floor treatment-

To begin with, it will not endure indefinitely. The anti-slip properties of the finish will wear away after a few years. And you’ll want to reapply for a fresh coat.

Second, it lacks the grip that carpet or anti-slip adhesive stair treads do. The coating is intended to make the floor less slippery. The friction generated by a layer of carpet, however, far outweighs the small particles in the finish. Or the specially designed sticky stair treads.

Using Non-Slip Paint Additives

Non-slip paint additives are just a bucket of sand that binds to the paint. It creates a sandpaper-like surface. Sand is entirely harmless when mixed with paint. And so, the addition has no effect on the colour or finish.

You may also control how much anti-slip ingredient goes into your paint. Simply apply a lesser amount of the additive if you require a ridged texture to your surface. You can add the full bucket or package if you want a denser, rougher texture.

You’ll be utilizing this product with paint. And wood paint is far different from ceiling paint and wall paint. So you won’t have to think about how it affects the finish of your wooden stairs. Because the paint will cover them. 

Eventually, the grit deteriorates the wood beneath it. However, removing the paint would need refinishing your wooden steps. Which would include sanding too.

There is no greater alternative than the non-slip colour additive if you want to paint your steps. And at the same time I want them to be anti-slip.

For painted hardwood surfaces, this is an excellent slip-proofing solution. Mixes well with a variety of paints. The grit level is adjustable.

Works exclusively with paint. Painting your staircase takes a long time. It’s quite tough to remove after it’s been applied.

That’s it! Whatever choice you make, make sure you follow the product’s instructions. 

FAQs

Question: How can a slanted staircase be made safe?

Answer: When a sheer stair is restructured, stepping space on one or both of the levels is lost. Reduce stair riser height and increase tread depth to make the stairs safer.

Question: Does making wooden stairs slippery make them slippery?

Answer: For increasing the shine on wooden stairs, you have to polish them. So, even if for a few days, it will be a little slippery. But slowly, the slippery effect cuts off.

Question: How can a slanted staircase be made safe?

Answer: Steep staircase generally necessitates the loss of living space on one or both sides of the floors.  To make the stairs safer to ascend and descend, lower the stair riser height. And raise the tread depth.

Conclusion

Thank you for taking the time to read this. You should now know how to make wood stairs non-slip.

We hope it has provided you with some inspiration. You can reach us with any of your queries. Till then, all the best!

Scott Kelly