Skip to Content

How to Remove Kohler Kitchen Faucet: Follow 10 Steps!

This article is for informational purposes. Always seek the advice of qualified professionals.

Struggling with fixing your Kohler kitchen faucet. It’s a common issue as the process is a bit different. So, do you need a professional? No, you need a complete guide. 

How to remove the Kohler kitchen faucet?

A few simple tools are needed to remove a Kohler kitchen faucet. It’s a simple DIY job and for that, you have to switch off the water and take out the aerator. First, replace the faucet diverter and then the faucet rings. Finally by replacing the handle and bonnet complete it.

It’s just a simple guideline. But I guess you need to know a bit deeper. So, let’s get started on learning how to accomplish this!

How to Remove Kohler Kitchen Faucet?

It is simple to remove the Kohler kitchen faucet. If you follow it step by step it won’t take long.

Additionally, if ever wanted to remove a restrictor from a faucet, that’s easy as well.The process of removing flow restrictor from bathroom faucet is similar to the kitchen faucet removal method.

Step 1: Gather the Equipment

Gather the equipment and resources you’ll need before you begin your remover project. This will make the procedure much simpler and far less frustrating. It will also help you to do the fix far quicker. What you’ll need is as follows-

  • 1/8″ Tool Allen
  • 3/8′′ Box Tool or Open End Tool
  • 1 1/16′′ Open Wrench or an adjusted tool with this size opening
  • Locking Channel
  • Hammer
  • Screwdriver with a Broad Blade 
  • Screwdriver, Small or knife-edged device
  • Pliers with a Needle-Nose
  • Towels, paper
  • a thick cloth, such as an old washcloth
  • Mild Cleaning Agent
  • Something to Protect the Sink Drain 
  • Light on the go

Step 2: Switch of the water 

Switch off the water while accessing the cartridge or removing the faucet entirely. Under your sink, you should find hot and cold water shutdown valves. 

Move them both to the right, then switch on the faucet to make sure the water is shut off. It’s worth remembering that the water shutdown valves sometimes “ice” due to inactivity. In that case, you should attempt to close the main water valve.

Step 3: Button to Remove the Faucet Plug

The plug button is a little circular button located underneath the faucet handle. Push the button out with the grip in the correct spot. 

If it isn’t readily removed, insert the tip of a tiny screwdriver beneath the faucet handle skirt, immediately while behind the plug button, and pull out. Using a thin breaking instrument, remove the button or your fingernail.

Step 4: Taking out the Aerator

According to Kohler, you don’t need to bother about shutting off the water; all you need to do is remove the aerator. But it will be safer to remove nut screws and other utilities if they are stuck.

The spout end of your Kohler kitchen faucet could easily twist off by turning it counterclockwise. If it appears to be trapped, wrap a cloth all around the end before twisting it off with an adjustable wrench. 

Next, using your thumb, simply press the aerator out.

The spray face surrounds the aerator on your lift faucet. Match up an adjustable wrench with the aerator’s straight lines and gently pull it out.

Step 5: Take out the Faucet Hub Assembly

Pull the hub assembly up and over the body of the faucet to remove it. Mineral accumulation may hinder the assembly from moving freely after years of use. Do not be scared to give it a good shove forward.

If it still won’t move, try inserting a wide-bladed screwdriver between the sink and the assembly. Carefully push up on the assembly until it comes free of the sink. 

Take care not to scratch the surface of the sink or hub assembly. You can prevent scratching the surfaces if you use a non-metallic screwdriver.

In search of non-metallic screwdrivers? Check out this table:

Product 1
Product 2

Using any of them will prevent scratching. Now let’s get back to the main point.

Step 6: Replace the Faucet Diverter

A Diverter is a little circular component positioned in the faucet’s rear. Once you can’t get out of there with your fingers, try needle-nose pliers.

With your fingers, push the new Diverter into position, fins pointing out.

Step 7: Getting to the Cartridge

You might not have to remove your Kohler kitchen faucet depending on the situation. 

If the spout or handle of your Kohler faucet is leaking, remove the handle to access the cartridge This cartridge’s replacement will resolve leakage and mobility difficulties. Look for a little oval behind the handle. 

Push a flat-head screwdriver under the circular tab to release the hex nut. Using an Allen wrench, remove the nut and handle.

Rotate the head counterclockwise to release it from the handle. Using an adjustable wrench, remove the kitchen faucet nut that is keeping the cartridge in place.

You must be able to see the cartridge immediately. It may be possible to take it out by hand at times, but you’ll need to use needle-nose hooks to gently pull it up and out. 

Step 8: Replace the Faucet Rings  

Remove the two o-rings and two bearings from the top and bottom of the faucet body. 

When replacing o-rings and bearings, wipe off the whole exterior surface of the faucet body to eliminate any loose dirt.

To the o-rings, apply the silicone lubricant that came with the Kohler replacement parts. Reconnect the o-rings and bearings in the opposite order they were withdrawn.

Step 9: Replace the Faucet Bonnet and Handle 

Return the bonnet to its original position. Then, replace the plugging button and secure the set screw on the handle.

Step 10: Tighten the Under-Sink Bracket

Tighten the bracket under the sink if somehow the faucet component became free from the sink during the repair.

Bravo, you have just completed the removal of your Kohler kitchen faucet.

FAQs

Question: How do you take a Kohler faucet head off?

Answer: Pull out the head, clamp the tube to keep the head from retracting. Then unscrew the head from the collar at the end of the tube to remove it.

Question: How do you unclog a Kohler faucet’s hose?

Answer: Getting Rid of: Insert one of the white tabs and slightly twist the black connection. This maintains the first white tab in place.

Question: How do you undo the nut behind the sink faucet?

Answer: Behind the sink basin from the cupboard and clutch the mounting nut that secures the faucet button tailpieces. 

Conclusion

This leads us to the end of our discussion. I am glad you liked learning how to remove Kohler kitchen faucets.

Finally, if you solve it quickly, simply change the spray head and it will be repaired.

Until then, be happy!