You’ve installed water pipes just a few days back. And you suddenly notice that your water pipes have got sand inside them. How annoying is that!
You sure want to get rid of that. Don’t know the process? It’s okay, we’ve got your back!
How to get rid of sand in water pipes?
Firstly, you need to boil some water. Shut the water system of your home and empty the pipes. Apply the drain cleaner and wait for a while. Then you need to boil the water again and pour it into the drains. Finally, you can turn on the water system again.
Still confused about how to get rid of sand in water pipes? Don’t worry, we have created a stepwise guide just for you.
Read along to find out more!
Why Is There Sand In Water Pipes?
Well, your pipes could have got sand for many reasons. But you need to make sure you know the reason behind yours to avoid it from happening again. We’ve mentioned the most common reasons why this happens.
Incorrect Gravel Size
Your water pipes can have sand inside them due to the incorrect size of gravel. During the water well construction, you need gravel packs. If the size doesn’t fit, sand would enter the pipes.
Hole In The Pipes
Holes in the water pipes can also be the reason for this issue. Because water jets through holes, stirring up sand. This type of water jetting might cause separation in the gravel packs.
As a result, sand will be able to get into your water pipes.
How To Get Rid of Sand in Water Pipes?- 7 Step Guide
Getting sand out of your water pipes is not a difficult task. We have mentioned the steps below. Make sure to follow these instructions properly. The process is easier than waterproofing your canvas tarp.
Step 1: Boil Hot Water
The very first thing you need to do is boil water of around 5 liters. Once you’re ready with hot water, you need to fill several pots with that water. Try to keep plenty of hot water.
You may consider keeping 5 liters of water. Because you’d need to have at least a pot of water for each drain.
Step 2: Shut Off The Water System
It’s always better to turn off the main water system when working on water-related stuff. Make sure you shut off the main water valve. Be careful when you’re rotating the handle.
This is because the water valve handle might break if you touch it roughly. Once you’re done turning it off, you’re good to start working.
Step 3: Empty The Pipes
Now, you need to empty the pipes. You’ve already turned off the main water system. You just need to turn on the faucets afterward. This would help empty the pipe by letting the water come out of the pipes.
After the water comes out and stops flowing, turn off the faucets.
Step 4: Fill The Pipes with Drain Cleaner
Now, you need to work with the drain cleaner. You can get your desired drain cleaners anywhere around you in the markets.
But you might still be confused to choose the best drain cleaner. No worries, we’ve got a couple of suggestions for you below-
| Product 1 | |
| Product 2 |
These cleaners are quite effective in drain cleaning!
After you’ve gathered your desired drain cleaner, it’s time to start using it. Fill out the pipes with the drain cleaner. You might be confused about how to use it and how long to keep it like that.
Worry not, you can actually get all the instructions in the packet of the drain cleaner. Make sure you follow the instructions properly.
If you use a chemical cleaner, it might take only about 15 minutes. On the other hand, a natural cleanser would take up to several hours.
Step 5: Boil The Water Again
You need to boil the water that you’ve previously kept in pots. After that, pour the boiled water into the drains.
Remember pouring hot water into the drains is helpful in many ways. And this is one of the ways in which you can get rid of centipedes in drains.
Make sure you’re pouring the water uniformly so that no part of the drains is left dry.
Step 6: Turning On Water System Back
It’s time to turn on the water system back. After you’re done, all the water pipes would get filled with water.
It would take a bit of time to refill. Because you had emptied the pipes after turning off the main water system.
Step 7: Final Move
Finally, you’re at the last phase. You can turn on the faucets now. Make sure you turn them on with the maximum speed.
This would help any leftover sand to come out of it. The calcium deposits would also flow out of the faucets.
Finally, your work is done!
Remember one thing! Sometimes the faucets get damaged during these processes. But you can obviously replace the faucets easily. If you’ve got delta or peerless faucets then you can just interchange them.
These are the directions to get rid of sand in water pipes.
FAQs
Question: Why is there sediment in my faucets?
Answer: Sometimes the water doesn’t come out of the tap or it comes out without fun. Then dirt and minerals can accumulate. This can clog the screen at the tip of the faucet. As a result, the faucet in the bathroom was clogged. In addition, the kitchen appliance can also splash every time it rotates. Therefore, sediment may be the culprit.
Question: Why is the water coming out so dirty?
Answer: Runoff from agricultural activities can bring animal manure, heavy metals, and chemicals into local waters. At the same time, in urban areas, sewer leaks can contaminate drinking water. Obsolete structures, like old pipes, submerge heavy metals in the water. As a result, the water turns quite dirty. Eventually, the entire water tank can get dirty!
Question: How to remove calcium deposits in the pipes?
Answer: Unfortunately, the only quick and safe way to repair a blocked pipe is to replace it. No state allows licensed plumbers to pour CLR drain pipe cleaner into pipes. So, you need to replace the pipe to remove any calcium deposits. And this would cost you some money.
Final Words
Now, you know how to get rid of sand in water pipes! We hope our directions are easy, simple, and effective to implement.
Make sure to stay back for any queries!
Wishing you the best for your home improvement!